Princeton Tec VIZZ RGB MPLS Instrucciones De Operacion Y Mantenimiento

VIZZ RGB MPLS
®
Operating and Maintenance Instructions
ENGLISH:
Battery Installation - See Figure 1
3 AAA
• Alkaline (LR03)
• Lithium (L92)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and recommends recycling
batteries. For more information about battery recycling, please go to
https://batterysolutions.com
Observe proper battery polarity. Improper installation of the batteries will
damage the light and void the warranty.
!
WARNING
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry types
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Lithium batteries offer extended constant brightness time,
extreme cold weather performance, and lighter weight. Rechargeable
NiCad or NiMH batteries may result in reduced brightness due to lower
nominal voltage.
The Vizz RGB battery compartment has a waterproof seal. It is important
to keep this seal free from dirt and away from harsh chemicals in order
to preserve waterproof integrity. Inspect the seal every time batteries
are changed. If dirt is present, wipe gently with a damp cotton swab and
mild soap until dirt is removed.
Switch Operation - See Figure 2
From off:
Press 1x -
Press 2x -
Press 3x -
Press 4x -
One Second Hold from any mode -
Press & Hold while in white mode -
Press 1x after more than 1 second
in any mode-
Five second hold -
From off, 5 second hold will lock light to prevent accidental Activation
and resulting battery drain. Removal and replacement of batteries will
also reset Vizz RGB to unlocked state.
Troubleshooting
If the Vizz RGB fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check circuit board for water (the seal may have be compromised by
improper rear cover installation or dirty seal). The light will resume nor-
mal operation once the water is shaken or blown out and the light is
left open until completely dry. If the light has been contaminated with
salt water, flush the unit with fresh water and dry as described above.
Vizz RGB MPLS Accessories
To attach the Vizz RGB Tactical MPLS to the NVG Shroud:
1. Slide the bracket arm into the NVG Shroud adapter plate, making
sure the pull tab is above the lip of the adapter plate and that the
male grooves on the bottom of the bracket arm are aligned inside
the female grooves on the bottom of the adapter plate.
2. Push the bracket arm securely into place, ensuring that the pull tab
audibly clicks over the lip of the NVG Shroud
adapter plate.
3. Your MPLS Headlamp should now be secured in the NVG Shroud.
You can rotate the headlamp to focus your light source accordingly.
To remove the MPLS headlamp from the NVG Shroud:
1. Remove the NVG Mount from your helmet.
2. Push up slightly on the bottom of the light housing.
3. While pushing upward, use the tool on the provided headstrap to
press the tab of the arm bracket towards the headlamp housing, so
that it disengages from the NVG Shroud adapter plate.
4. Slide the headlamp unit out of the NVG Shroud adapter plate.
Figure 1 – Battery Replacement
1
Figure 2 – Switch Operation
Figure 3 – Performance
(ANSI FL-1 Standard)
Runtime is defined as the duration of time from the initial light output value—defined as 30 seconds after the point the device is first turned on—
using fresh batteries, until the light output reaches 10% of the initial value.
Reserve time is the duration of time from 10% of initial light output value down to 0.25 lux
Figure 4 – Mounting System
1
Red
Green
Blue
Off
White
Dimming To attach the MPLS Headlamp to the Butterfly Mount:
1. Slide the bracket arm into the Butterfly Mount, making sure the pull
Off
tab is above the lip of the mount and that the male grooves on the
Lockout/Unlock
bottom of the bracket arm are aligned inside the female grooves on
the bottom of the mount.
2. Push the bracket arm securely into place, ensuring that the pull tab
audibly clicks over the lip of the Butterfly Mount.
3. Your MPLS Headlamp should now be secured in the Butterfly Mount.
The mount can be attached to the provided headstrap, MOLLE
straps, or any 1" webbing. You can rotate the headlamp to focus
your light source accordingly.
To remove the MPLS headlamp from the Butterfly Mount:
1. Push up slightly on the bottom of the light housing.
2. While pushing upward, use the tool on the provided headstrap to
press the tab of the arm bracket towards the headlamp housing, so
that it disengages from the Butterfly Mount.
3. Slide the headlamp unit out of the Butterfly Mount.
USA Lifetime Warranty - International 10-YearWarranty
Due to International regulations, Princeton Tec's lifetime warranty can
only be offered to customers in the USA. Princeton Tec offers a 10-year
warranty to our customers outside the USA. FULL WARRANTY - Princeton
Tec warrants this product to be free from defects in workmanship and
materials under normal use for as long as you own this product. This
warranty covers all of the component parts of the product except
batteries. This warranty does not cover deterioration due to normal
wear or damage due to misuse, alteration, negligence, accidents, or
unauthorized repair. Princeton Tec will repair or replace parts which
are defective In workmanship or materials. Your authorized Princeton
Tec Dealer and Princeton Tec are the only facilities authorized to repair
the product. After (3) unsuccessful attempts to repair the product, you
have the right to elect replacement of the product or a refund of the
purchase price less allowance for use of the product. NO INCIDENTAL
OR CONSEQUENTIAL DAMAGES ARE INCLUDED IN THIS WARRANTY.
(Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not
apply to you.) This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
2
Press 1x:
Red
Press 2x:
Green
Press 3x:
Blue
Press 4x:
Off
Modes Lumens Runtime Beam Pattern
HIGH SPOT 550 2.5
LOW SPOT 40 33h
RED 3 45h
GREEN 5 55h
BLUE 3 40h
DISTANCE (m) 0 5
2
3
1s hold in any mode:
White 80%
From white:
Hold:
Dimming
After 1s in any mode:
Press 1x from On:
Off
20 25
1
Princeton Tec reserves the right to change product specifications
without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a chemical known to
the State of California to cause birth defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, first contact
Princeton Tec customer service on
1-800-257-9080 to request an RMA number. Please have your
light model, date of purchase and a brief description of the fault
you are experiencing. No warranty repairs will be accepted without
an RMA number.
3. Return the light without batteries to:
Princeton Tec, PO Box 8057 Trenton NJ 08650. Postage due and
freight collect items will not be accepted.
4. Upon receipt your light will be processed in about two weeks.
Please allow additional time for return transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2023 Princeton Tec
4
Press 5s:
Lock-Out
Press 5s from Lock:
Unlock
Reserve
70h
80h
45h
100h
40h
95
2