Publicidad
Idiomas disponibles
Idiomas disponibles
Thank you for buying a HIGHSIDER product. Because of our passion for motorcycles all our products are designed to meet your needs as a motorcyclist. We wish you always a safe and pleasant ride with your new HIGHSIDER product
from Paaschburg & Wunderlich GmbH.
The installation should be conducted by a qualified person according to the ECE standard. If the installation violates the ECE standard the liability for the product will be lost. The emitting direction of the light must be oriented parallel
to the ground and the longitudinal axis of the vehicle. The indicator can be installed in a vertical or horizontal orientation. This indicator is approved for the use on motorcycles. The product complies with the current ECE standard. This
means no registration or carriage of documentation is needed when installing it onto your motorcycle. Please keep this manual for a later use!
CAUTION:
If uncertain about the installation please hire a qualified person. Never look directly into the LED lights! Any modification of the item is prohibited and will cause loss of warranty and liability.
Scope of delivery:
•
1 Pair indicator (Fig 1)
Assembly of the Indicator
1. Disconnect the battery from the electric system and assure that your motorcycle stands solidly on the ground. Before final installation a functional test is recommended.
2. The correct cable connection is explained in the text box below.
CAUTION:
Only connect to 12V DC power supply. Disregarding this will result in loss of warranty.
3. Always install the indicators symmetrically to the center of your motorcycle!
4. All cables must be laid out carefully and in a professional manner. Prevent sharp bending of cables. Open cable ends must be well insulated.
5. Always install the indicators in pairs. Make sure no accessories like bags etc. affect the light distribution of the indicator.
6. In vehicles equipped with CAN-bus systems or in some cases ABS systems, error codes can occur. This is due to the reduced electrical resistance of the LED indicator. The installation of an additional resistor (in parallel) can resolve
this issue.
7.
CAUTION:
After installation, the proper function of the ABS system/CAN-bus system must be checked!
8. If the indicating frequency is too high, additional resistors installed in parallel to the indicator or the use of a load independent indicator relay will remedy the problem. When using resistors, care must be taken to ensure good
heat dissipation.
CAUTION:
In case of indicator failure, no change of the indicating frequency will occur. Due to this, the indicating function needs to be checked before each ride!
Find suitable housings, turn signals, taillights, power resistors, electronic flasher relays, adapter cables and other accessories in our Webshop!
Cable connection:
Connect to 12V DC only!
Black – ground (-)
Yellow – indicator
(+)
Before each ride: It is the duty and responsibility of the rider to regularly check and maintain the safety-related vehicle parts. Before starting your journey, check the correct adjustment and function of the HIGHSIDER products and the tightness of all screwed connections.
Warranty: Take the time to do a 100% professional job of installing the HIGHSIDER products. Take into account all our installation and safety instructions.
A faulty, improper installation or handling of the product will void the warranty.
Maintenance/Care: Do not use aggressive detergents to care for the HIGHSIDER products. The HIGHSIDER products can be perfectly cleaned with a simple, lukewarm detergent solution. Contact with brake fluid, brake cleaner, fuel, etc. should be avoided. Immediately pick
up any unintentionally applied impurities with a soft cloth and clean the surface with detergent solution
Enviromental Information: This product may not be disposed in the normal household rubbish at the end of its lifetime. The disposal can be done through the Paaschburg u. Wunderlich customer service or a local return and waste collection institution.
HIGHSIDER Tips & Tricks on
https://www.youtube.com/c/HIGHSIDERTippsTricks
Exclusion of liability and warranty regulation:
In the event of improper handling, installation or use of the device, warranty and guarantee claims may expire. Due to the non-verifiability of the correct application, Paaschburg und Wunderlich GmbH assumes no liability for direct or indirect damage or consequential damage resulting from the operation of the device.
This does not apply if the damage is based on intent or gross negligence on the part of Paaschburg & Wunderlich GmbH, or if the damage consists in injury to life, limb or health, or Paaschburg & Wunderlich GmbH has culpably violated an essential contractual obligation (cardinal obligation).
Paaschburg & Wunderlich GmbH, Am Alten Lokschuppen 10a, D-21509 Glinde (GER),
Tel.: +49 (0) 40 248 277-0; E-Mail:
sales@pwonline.de
204-363A_Rev00_2022-11
Mounting and safety instructions
HIGHSIDER LITTLE & BRONX-MX LED indicator
Please read this manual carefully prior to installation.
Fig. 1
:
You can find more
www.highsider-germany.de
LITTLE BRONX-MX:
A: 26 mm
C: 12 mm
D: 15 mm
BRONX-MX:
A: 45 mm
B: 12 mm
D: 18 mm
products at:
www.highsider-germany.de
All rights reserved. Changes and errors are excepted.
Abbildung ähnlich/
Image similar/
Image similaire/
Imagen similar
Seite 2 von 4
Publicidad
