KUNERT ROY Manual De Instrucciones página 10

result (fig. 17). If a new born baby is put in the stroller, it is recommended to set the position of the seat
which is to be used from the baby's birth in a position similar to a lying one.
The backrest can be adjusted in 4 positions. To lift the backrest up, you need to pull up the lever from under
the back of the seat and at the same time pull up the backrest up until you reach the desired position.
Next, release the lever (fig. 18). To recline the backrest, you need to pull up the metal lever, place it in the
desired position and release the lever.
To unfold the frame, lay it flat (Fig. 1), press the protection (Fig. 3) and then, holding the handle, pull it
vigorously up until the locking mechanisms click (Fig. 2). ATTENTION! Before using the stroller, make sure
that the locking mechanisms are locked, tighten them if ecessary. - to fold the frame, press the lock button
inside with your thumb (fig. 3) and at the same time pull the levers on both sides of the handle. (fig. 4) and
at the same time pressing them downwards. - ATTENTION! Before assembling the frame, disassemble the
gondola. Otherwise, this operation may be difficult.
The pram has front swivel wheels with a lock of the straight-ahead push. In order to lock the wheels, first
position them parallel to the rest of the pram and then turn the rim to the right (fig. 29). In order to unlock
the front wheels to go in all directions, simply turn the rim to the left.
To unfold the pram chassis, lay it down flat, push the lock (fig. 1) and pull it up strongly while holding the
handle until the locking mechanism will lock into place (fig. 2). WARNING! Before using the pram, ensure
the locking mechanisms are activated, if not, pull them tighter.
The chassis may be folded in two ways (with and without wheels):
-to fold the chassis with the wheels, first lock the front wheels by positioning them across the to the pram.
Then, press the lock button with your thumb (fig. 3) and then simultaneously pull the levers on both sides
of the handle (fig. 4). -to fold the chassis without wheels, take off two front wheels (fig. 5) and rear wheels
(fig. 6). Then, press the lock button with your thumb (fig. 3) and simultaneously pull the levers on both
sides of the handle (fig. 4).
To activate the parking device, you need to step on the lever at the bottom of the pram (fig. 28). The
parking device will be released when the lever is lifted.
The footrest can be adjusted by simultaneously pressing side buttons while putting it in the desired
position (fig. 19).
Before mounting the wheels, first mount the axes in the pram chassis. In order to mount the axes, push the
larger end of the axis into the absorber by pressing the red button, and then release the button. Mount the
axes on both sides of the pram and check whether fixed properly (fig. 9). To mount the rear wheels, press
the metal button in the central part of the wheel (fig. 6) and then slide the wheel on the axis as far as it will
go, release the button and pull back the wheel until you hear a "click" sound. Always check whether the
wheels are mounted correctly. In case the pram wheel comes of when pulled, repeat the wheel mounting
procedure until mounted properly.
To install the front wheels, insert the fork axle with the pin into the turntable (fig. 5). To unclip the turntable,
press the lock button and pull out the turntable with the wheel. Always check that the wheels are correctly
mounted after installing the wheels. In a situation where the wheel of the stroller falls off after pulling,
repeat the assembly of the wheels until the wheels are correctly installed.
BACKREST ADJUSTMENT
UNFOLDING AND FOLDING THE TROLLEY FRAME
SWIVEL FRONT WHEELS
FOLDING AND UNFOLDING THE PRAM CHASSIS
PARKING DEVICE
FOOTREST ADJUSTMENT
MOUNTING AND REMOVAL OF REAR WHEELS
ASSEMBLY AND REMOVAL OF FRONT SWIVEL WHEELS
FASTENING THE HARNESS
10