Publicidad
Idiomas disponibles
Idiomas disponibles
ADDITIONAL SPECIFIC SAFETY RULES
1.
DO NOT OPERATE THIS MACHINE until it is
completely assembled and installed according to
the instructions. A machine incorrectly assembled
can cause serious injury.
OBTAIN ADVICE from your supervisor, instructor,
2.
or another qualified person if you are not thor-
oughly familiar with the operation of this machine.
Knowledge is safety.
3.
FOLLOW ALL WIRINg CODES and recom-
mended electrical connections to prevent shock
or electrocution.
4.
kEEP kNIVES SHARP and free from rust and
pitch. Dull or rusted knives work harder and can
cause kickback.
5.
NEVER TURN THE MACHINE "ON" before clearing
the table of all objects (tools, scraps of wood,
etc.). Flying debris can cause serious injury.
NEVER TURN THE MACHINE "ON" with the work-
6.
piece contacting the cutterhead. Kickback can
occur.
7.
SECURE THE MACHINE TO A SUPPORTINg
SURFACE to prevent the machine from sliding,
walking or tipping over.
8.
PROPERLY SECURE THE kNIVES IN THE CUTTER-
HEAD before turning the power "ON". Loose
blades may be thrown out at high speeds causing
serious injury.
LOCk THE SPEED SETTINg SECURELY before feed-
9.
ing the workpiece through the machine. Changing
speeds while planing can cause kick-back.
10. AVOID AWkWARD OPERATIONS AND HAND
POSI- TIONS. A sudden slip could cause a hand
to move into the knives.
11. kEEP ARMS, HANDS, AND FINgERS away from
the cutterhead, the chip exhaust opening, and the
feed rollers to prevent severe cuts.
12. NEVER REACH INTO THE CUTTERHEAD AREA
while the machine is running. Your hands can be
drawn into the knives.
13. DO NOT STAND IN LINE OF THE WORkPIECE.
Kickback can cause injury.
14. ALLOW THE CUTTERHEAD TO REACH FULL
SPEED before feeding a workpiece. Changing
speeds while planing can cause kickback.
Refer to them often and use them to instruct others.
All manuals and user guides at all-guides.com
Failure to follow these rules may result in serious injury.
SAVE THESE INSTRUCTIONS.
15. WHEN PLANINg BOWED STOCk, place the concave
(cup down) side of the stock on the table and cut
with the grain to prevent kickback.
16. DO NOT FEED A WORkPIECE that is warped, con-
tains knots, or is embedded with foreign objects
(nails, staples, etc.). Kickback can occur.
17. DO NOT FEED A SHORT, THIN, OR NARROW WORk-
PIECE INTO THE MACHINE. Your hands can be
drawn into the knives and/or the workpiece can
be thrown at high speeds. See the "OPERATION"
section of this instruction manual for details.
18. DO NOT FEED A WORkPIECE into the outfeed end of
the machine. The workpiece will be thrown out of
the opposite side at high speeds.
19. REMOVE SHAVINgS ONLY with the power "OFF" to
prevent serious injury.
20. PROPERLY SUPPORT LONg OR WIDE WORkPIECES.
Loss of control of the workpiece can cause serious
injury.
21. NEVER PERFORM LAYOUT, ASSEMBLY or set-up
work on the table/work area when the machine is
running. Serious injury will result.
22. TURN THE MACHINE "OFF", DISCONNECT IT FROM
THE POWER SOURCE, and clean the table/work
area before leaving the machine. LOCk THE
SWITCH IN THE "OFF" POSITION to prevent
unauthorized use. Someone else might accidentally
start the machine and cause injury to themselves or
others.
23. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute,
1300 Sumner Avenue, Cleveland, OH 44115-2851
(www.powertoolinstitute.com).
also available from the National Safety Council,
1121 Spring Lake Drive, Itasca, IL 60143-3201.
Please refer to the American National Standards
Institute ANSI 01.1 Safety Requirements for
Woodworking Machines and the U.S. Department
of Labor Regulations.
4
Information
is
Publicidad
