Grounding Instructions; Extension Cords; Unpacking And Set-Up - Shop-Vac 87M Serie Manual Del Usuario

This appliance must be grounded. If it should malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock. This appli-
ance is equipped with a cord having an equipment-grounding conductor and grounding plug.
The plug must be inserted into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WArNING
– IMPROPER CONNECTION OF THE EqUIPMENT-
GROUNDING CONDUCTOR CAN RESULT IN A RISk OF ELECTRIC SHOCk.
CHECk WITH A qUALIFIED ELECTRICIAN OR SERVICE PERSON IF YOU
ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY GROUNDED.
DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE – IF IT WILL
NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A qUALI-
FIED ELECTRICIAN.
This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks
like the plug illustrated in sketch A. A temporary adaptor that looks like the adaptor illustrated
When using the appliance at a distance where an extension cord becomes necessary, a 3-conductor
grounding cord of adequate size must be used for safety, and to prevent loss of power and overheating.
Use the table below to determine A.W.G. wire size required. To determine ampere rating of your vacuum,
refer to nameplate located on rear of motor cover. Before using appliance, inspect power cord for loose
or exposed wires and damaged insulation. Make any needed repairs or replacements before using
your appliance. Use only three-wire outdoor extension cords which have three-prong grounding-type
plugs and three-pole receptacles which accept the extension cord's plug. When vacuuming liquids, be
sure the extension cord connection does not come in contact with the liquid.
NOTE: STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS
LOW. THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE APPLIANCE. TO REDUCE THE
FREqUENCY OF STATIC SHOCKS IN YOUR HOME, THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR
WITH A CONSOLE OR INSTALLED HUMIDIFIER.

UNPACkING AND SET-UP

1. Pull lid latches in an outward motion, remove tank cover and any accessories which may have
been shipped in the tank.
2. Attach caster system following the instructions and illustrations in this manual.
3. Before replacing tank cover, refer to Dry Pick Up or Wet Pick Up Operation in this manual to
ensure you have the proper filters installed for your cleaning operation.
4. Replace tank cover and apply pressure with thumbs to each latch until it snaps tightly in place.
Make sure both lid latches are clamped securely.
5. Insert long machine hose end with locking-nut into inlet of tank and tighten.
Do not over-tighten.
6. Attach the extension wands to the accessory end of the hose. Twist slightly to tighten the
connection (Figure A).
7. Attach one of the cleaning accessories (depending on your
cleaning requirements) on the extension wands. Twist slightly
to tighten the connection (Figure A).
8. Plug the cord into the wall outlet. Your cleaner is ready for use.
I = ON, O = OFF
NOTE: MANY MORE USEFUL TOOLS ARE AVAILABLE AT YOUR LOCAL DEALER OR
SHOP-VAC ® WEBSITE.
CASTER SYSTEM ASSEMBLY
Not all units are equipped with the same caster system. Follow the instructions that apply
to your specific unit.
PLASTIC TANk:
With Four Caster Feet
You will find four caster feet, four casters and four screws (Figure 1) with your wet/dry vacuum.
Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that bottom is facing up.
2. With front of tank facing you, take caster feet marked with the letter A (Figure 2) and place
in slots on left front and right rear of tank also marked with the letter A (Figure 3) and
secure with screws provided (Figure 4).
3. Take caster feet marked with the letter B (Figure 5) and place in slots on right front and
left rear of tank also marked with the letter B (Figure 6) and secure with screws provided
(Figure 7).
4. If flat washers are included in hardware package place flat washer over stem of caster
before installing casters into feet. NOTE: Flat washers are not required with all units.
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 8).
6. Return tank to upright position.
2
1
A

GROUNDING INSTRUCTIONS

EXTENSION COrDS

A
3
4
A A
A
B
A
A
in sketches B and C may be used
to connect this plug to a 2-pole
receptacle as shown in sketch B
if a properly grounded outlet is not
available. The temporary adaptor
should be used only until a properly
grounded outlet (sketch A) can be
installed by a qualified electrician.
The green colored rigid ear, lug or
the like extending from the adaptor
must be connected to a permanent
ground such as a properly grounded
outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.
IN CANADA, THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN
ELECTRICAL CODE. Make sure that the appliance is connected to an outlet having the same
configuration as the plug. No adapter should be used with this appliance.
Volts Total length of cord in feet
120V 25
Ampere Rating
More Not More
Than Than
0 - 6
18
6 - 10
18
10 - 12
16
12 - 16
14
5 6
B
B
B
A
B
With Rear Caster Dolly
You will find four casters (b.), two caster feet (c.), rear caster dolly/tool holder (d.), and four screws
with your wet/dry vacuum. Assemble as follows:
b
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so that
the bottom is facing up.
2. Take rear caster dolly and place into slots (on rear of tank, opposite of drain) and secure with
screws provided (Figure 9).
3. If flat washers are included in hardware package place flat washer over stem of caster before
installing casters into rear caster dolly. NOTE: Flat washers are not required with all units.
4. Insert casters into bottom of rear caster dolly by placing stem of caster into holes provided.
Apply pressure and twisting motion until casters snap into place (Figure 10).
5. With tank drain facing you, take caster foot marked with the letter A (Figure 11) and place in
slot on left side of tank also marked with the letter A and secure with screw provided (Figure
12).
6. Take caster foot marked with the letter B (Figure 13) and place in slot on right side of tank also
marked with the letter B and secure with screw provided (Figure 14).
7. Insert casters into feet by placing stem of casters into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 15).
8. Return tank to upright position.
9. Place tool basket (not standard with all models) with curved surface against tank on rear
caster dolly assembly (Figure 16).
10
9
13 14
A
B
A
50 100
AWG
16 16
16 14
16 14
12 Not recommended
7 8
A
B
B
c d
11
12
A
A
15 16
B
150
14
12
12