Cordless Screwdriver - Bort BAS-36N-Li Instrucciones De Servicio

English

Cordless screwdriver

TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1. On/off switch
2. Ring for torque control
3. Knob for locking/adjusting handle
4. Switch for changing direction of rotation
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, fi re
and/or serious injury.
• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
• Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
• Avoid damage that can be caused by screws, nails
and other elements in your workpiece; remove them
before you start working
• Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the charg-
er (chargers with a rating of 230V or 240V can also
be connected to a 220V supply)
• In case of electrical or mechanical malfunction, im-
mediately switch off the tool or unplug charger from
power source
• SBM Group can assure flawless functioning of the
tool only when original accessories are used
• Use only accessories with an allowable speed
matching at least the highest no-load speed of the
tool
• This tool should not be used by people under the age
of 16 years
• Be careful not to drill or drive into areas where elec-
trical wires may be contacted
• Do not touch the contacts in the charger
• Do not expose tool/charger/battery to rain
• Never charge battery outdoors
• Store tool/charger/battery in locations where tem-
perature will not exceed 40°C or drop below 0°C
• Batteries will explode in fire, so do not burn battery
for any reason
• When damaged, and under extreme usage and tem-
perature conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quick-
ly with soap and water, then with lemon juice or vin-
egar
- if liquid gets into the eyes, flush eyes with clean wa-
ter for a minimum of 10 minutes and seek immedi-
ately medical attention
1
2
• When battery is not in tool or charger, it should be
kept away from metal objects such as nails, screws,
keys etc. to prevent short-circuit
• Do not use charger when damaged; take it to one of
the officially registered SBM Group Service Stations
for a safety check
• Do not use battery when damaged; it should be re-
placed immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable bat-
teries with the charger WHEN CONNECTING NEW
3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live)
wire in the cord of the charger to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left
unattended
To ensure longer service life and proper
performance of the battery, take the following
actions when you start using new battery:
1. Use the new battery, without recharging it, till its
complete discharge.
2. Then charge the battery for 5-7 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times
to reach the nominal battery capacity.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These
solvents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please
contact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most
of the packaging materials can be recycled. Take
these materials to the appropriate recycling locations.
Take your unwanted machines to your local SBM
Group dealer. Here they will be disposed of in an
environmentally safe way.
NiCd batteries can be recycled. Deliver them to a disposal
site for chemical waste so that they can be recycled or
disposed of in an environmentally friendly manner.
GB
7