General Safety Norms - ADEO SCREEN INCEEL Manual De Uso

ENGLISH – Motorized screen user manual
This manual is an integral part of the product and must be read and understood in all its parts for safety reasons. It contains norms and directions for correct and safe use of the screen.
The manual should never be separated from the product; it must be stored in a suitable place to ensure its integrity, and in such a way as to be easily consulted by authorised personnel.
Product user shall be responsible for the manual's safekeeping. User shall also be responsible for checking the screen's functionality and for the repair or replacement of any damaged
parts that could pose a hazard.
Images contained in this manual are intended to provide a detailed description of the product's functions, characteristics and procedures. Any slight difference, depending on the model
represented, will not change the meaning that the images convey.
The screen product is manufactured in compliance with the provisions of the following EC directives 2006-95-CE LDV
The screen described in this manual must be used exclusively as a support for video projection. Any other use not covered by this manual, it is not consented.
The screen contains one or more Fabric of projection. The Fabric of projection is a cadmium-free plastic pvc sheet or Glass wire (continuos filament) plastified PVC impregnated, any fabric can be classified in
category:
- M1 and M2 fire classification under French standards (LNE Laboratoire national de métrologie et d'essais – SME Centre de recherches du Bouchet - WARRINGTONFIRE GENT Laboratoire de
métrologie et d'essais – IFTH Laboratoire accreditè
- B1 and B2 fire classification under German standards (LNE Laboratoire national de métrologie et d'essais – SME Centre de recherches du Bouchet - WARRINGTONFIRE GENT Laboratoire
national de métrologie et d'essais)
- UL94HB fire classification under USA standards (THE GOVMARK Organization, Inc.)
In the absence of a standardisation at a European level of the various national classification norms, it should be noted that the French M1 class corresponds to non flammable material and that M2 class
corresponds to flame retardant material.
Ensure that the screen has suffered no damage during transport. Should any fault be detected, promptly notify your dealer. Verify that all screen accessories have been included
-(2) n°8 threaded bars M8
-(3) n°4 Spacer nuts M8x30
-(4) n°4 Washers
-(5) n°4 Nuts M8
-(6) n°4 Thread stops M8
-(7) n°4 Base plates M8
-(8) n°2 Ceiling plugs
-(9) n°1 Plastic hex wrench
(only for standard motor screen models)
-(10) n° 1 unipolar selector switch (only for standard motor screen models)
-(11) n° 1 RF transmitter (Only for integrated radio screen models
-n°1 instructions booklet
(screws and plugs for wall mount are not included)
CAUTION do not use cutters or sharp objects to open the wrapping, always use protection gloves when unpacking, handling and installing the product. Depending on the product's weight (reference load: 25
Kg male – 15 Kg female), handling and installing operations should be performed by two, three or four people at least. For heavier loads we recommend the use of specific lifting equipment.
Always read the instructions and warnings set out in this manual very carefully before using the product or before performing any maintenance interventions.
Installation of the screen above passageway is strictly forbidden.. Before and during use, check that the screen poses no risk of hazard.
Do not tamper with, remove or damage any part or component of the screen.
Never perform screen maintenance operations when the motor is on (for maximum safety, remove power supply).
Not children safe. It is mandatory to keep children away during operations with the screen.
All our screens are covered by guarantee; validity of the same shall be subject to user's full compliance with the instructions contained in this manual.
WARNING: Faulty installation may compromise the safety of the product's operators; manufacturer shall not be held liable for damages to persons or things resulting from faulty
installation, improper use, insufficient or inadequate maintenance of the screen.
Manufacturer shall not be held responsible for problems associated with installation errors.
Screen installation, electrical connections and verifications in case of malfunction of motorised rolling screens must be performed by authorised vendor or by personnel that is
informed and trained in electrical hazards. The connection cable cannot be replaced. If the cable is damaged the screen must be replaced. Tampering with end stops or piercing
the seal placed over holes shall entail the forfeiture of the guarantee. For any necessary clarifications please contact our technical office.
N.B.ONCE THE SCREEN HAS BEEN MOUNTED ON THE BRACKETS, AND PRIOR TO USING IT, USER IS MANDATORILY REQUIRED TO ENSURE THAT THE SCREEN'S POSITION IS
PERFECTLY HORIZONTAL.
Made by Adeo Screen sp. Z o.o. (Polska) Specifications are subject to change without notice. E&OE
Doc: INCEEL Installation Manual rev4 | 17.09.2014
Please verify that you are working with the latest revision of this document before specifying your screen.
01 INTRODUCTION
02 GENERAL CHARACTERISTICS OF THE PRODUCT
2004-108-CE EMC
1999-05-CE R&TTE
2005-32-CE Eco design
2011-65-CE ROHS
2002-96-CE RAEEi
2001-95-CE SAFETY
03 UNPACKING AND HANDING THE SCREEN

04 GENERAL SAFETY NORMS

Page 7