Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
DISCO ABRASIVO DE ÁNGULO RECTO .75 HP
MEULEUSE DIE GRINDER À ANGLE DROIT ,75 HP
.75HP
WARNING
RATED RPM OF THE
RPM
RPM
RPM
ACCESSORY USED MUST
EXCEED THE MAXIMUM
TOOL RPM SHOWN
ALWAYS READ
INSTRUCTIONS BEFORE
USING POWER TOOLS
ALWAYS WEAR
SAFETY GOGGLES
ALWAYS WEAR HEARING
PROTECTION
ALWAYS WEAR FACE
PROTECTION
ALWAYS WEAR HAND
PROTECTION
AVOID PROLONGED
EXPOSURE TO VIBRATION
RIGHT ANGLE
DIE GRINDER
Max. Free Speed .............................................................20,000 RPM
Collet Size ......................................................................................1/4"
Air Inlet ................................................................................. 1/4" NPT
Vibration Level ...................................................................... 0.9 m/s²
Horse Power ................................................................................. 0.75
Min. Air Hose Size ...................................................................3/8" ID
Average Air Consumption ................................................... 3.4 CFM
Recommended Air Pressure ..................................................90 psig
Sound Level ............................................................................85 dBA
Length ...............................................................................................7"
Net Weight ............................................................................... 1.8 lbs.
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
S P E C I F I C A T I O N S
WARNING
Copyright © Professional Tool Products, 2018
MT4883
MT4883G
MT4883O
• Operating Instructions
• Warning Information
• Parts Breakdown
All rights reserved
Publicidad
Manuales relacionados para Matco Tools MT4883G
Resumen de contenidos para Matco Tools MT4883G
- Página 1 MT4883 MT4883G MT4883O DISCO ABRASIVO DE ÁNGULO RECTO .75 HP MEULEUSE DIE GRINDER À ANGLE DROIT ,75 HP .75HP RIGHT ANGLE • Operating Instructions • Warning Information DIE GRINDER • Parts Breakdown S P E C I F I C A T I O N S Max.
- Página 2 If the manual or product labels are lost jewelry or loose clothing. Secure long hair. Scalping or not legible, contact Matco Tools for replacements. can occur if hair is not kept away from tool and If the operator is not fluent in English, the product accessories.
- Página 3 MT4883, -G, O .75 HP RIGHT ANGLE DIE GRINDER OPERATION force which could be hazardous and cause mounted spindle to bend or break. Always turn off the air supply, drain hose of air pressure and detach tool from air supply before installing, removing NOTE: During operation, safety goggles should always be or adjusting any part or accessory on this tool, or before worn to guard against flying debris (users and bystanders).
- Página 4 MT4883, -G, O .75 HP RIGHT ANGLE DIE GRINDER WARRANTY Matco warrants this air tool for a period of 1 year to the consumer. NATIONAL MACHINE GROUP We will repair any MT Series air tool covered under this warranty AIR TOOL REPAIR CENTER which proves to be defective in material or workmanship during 1330 Commerce Dr.
- Página 5 MT4883, -G, O .75 HP RIGHT ANGLE DIE GRINDER Item Parts No Parts Name Item Parts No Parts Name RS15401 Regulator RS820R23 Rotor RS288302 O-Ring (P10) RS29022A Cylinder RS288303 O-Ring (P9) RS520118 Pin (2x6L) RS288304 Snap Ring RS820R25 Bearing Spacer RS246605 O-Ring (3.5 x 1.4) RS29125A...
- Página 6 MT4883 MT4883G MT4883O DISCO ABRASIVO DE ÁNGULO RECTO .75 HP .75HP RIGHT ANGLE • Instrucciones de Operación DIE GRINDER • Inforación de Advertencia • Revisión de Refacciones E S P E C I F I C A C I O N E S Velocidad libre máxima ..........20,000 RPM...
- Página 7 • El aire bajo presión puede ocasionar alguna herida severa. Nunca dirija el aire hacia usted ni a otros. • Use los accesorios recomendados por Matco Tools. Apague siempre la alimentación de aire, vacíe la • No lubrique las herramientas con soluciones inflamables manguera de toda presión de aire y separe la herramienta...
- Página 8 MT4883, -G, O DISCO ABRASIVO DE ÁNGULO RECTO .75 HP LA OPERACIÓN amoladora, reponga el disco abrasivo, la lima giratoria o la fresa de carburo. Siempre apague el suministro de aire, vacíe la manguera de la presión de aire y desconecte la herameitna del suministro Al momento de usar la amoladora, tenga cuidado de no ejercer de arie antes de instalar, extraer o ajustar cualquier parte o un esfuerzo excesivo el cual podría ser peligroso o ocasionar...
- Página 9 MT4883, -G, O DISCO ABRASIVO DE ÁNGULO RECTO .75 HP GARANTÍA Matco garantiza esta herramienta neumática por un periodo de NATIONAL MACHINE GROUP un año para el consumidor. Reparemos cualquier herramienta AIR TOOL REPAIR CENTER neumática de la Serie MT, cubierta bajo esta garantía, la cual 1330 Commerce Dr.
- Página 10 MT4883 MT4883G MT4883O MEULEUSE DIE GRINDER À ANGLE DROIT ,75 HP .75HP RIGHT ANGLE DIE GRINDER • Instructions de fonctionnement • Avertissement • Pièces S P É C I F I C A T I O N S Vitesse Max. à vide ........... 20 000 tr/min Grandeur de collet ..............
- Página 11 étiquettes du produit sont perdus ou illisibles, contactez doivent demeurer hors de portée de l’outil et de ses Matco Tools pour les faire remplacer. Si l'utilisateur- accessoires pour éviter tout scalp accidentel. Tenez opérateur de l'appareil ne maîtrise pas bien l'anglais, les cravates et les colliers hors de portée de l’outil, car...
- Página 12 MT4883, -G, O MEULEUSE DIE GRINDER À ANGLE DROIT ,75 HP FONCTIONNEMENT limeuse rotative ou la fraise au carbure. Toujours couper l'arrivée d'air comprimé et débrancher Faites attention, lorsque vous utilisez le Grinder, de ne pas l'outil avant d'enlever ou de mettre en place une pièce ou utiliser de force excessive ce qui pourrait être dangereux et un accessoire quelconque, ou avant d'effectuer une tâche causer le bris ou une courbure de la tige.
- Página 13 MT4883, -G, O MEULEUSE DIE GRINDER À ANGLE DROIT ,75 HP GARANTIE Matco garantit ses outils pneumatiques au consommateur pendant NATIONAL MACHINE GROUP une période d’un an. Nous réparerons tout outil pneumatique de AIR TOOL REPAIR CENTER la série MT couvert par cette garantie qui présente un défaut de 1330 Commerce Dr.