Descargar Imprimir esta página

Doosan DCT15BV Operación Y Mantenimiento página 18

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 22
LUBRICATION
Protec Engine Oil
Always use an air line lubricator with these tools.
We recommend the following Lubricator–Unit and Lubricant.
In Line Lubricator:
Lubricant: Protec Engine Oil
Attach the lubricator as close to the tool as pratical.
After every two or three hours of operation and at the
beginning of each work shift, if an air line lubricator is not
used, disconnect the air hose and pour about 3 cc of oil into
the air inlet of the tool.
Before storing the tool or if the tool is to be idle for a period
exceeding twenty-four hours, pour about 3 cc of oil into the
air inlet and operate the tool for 5 seconds to coat the internal
parts with oil.
INSTALLATION
Air Supply and Connections
Always use clean, dry lubricated air. Dust, corrosive fumes
and/or excessive moisture can ruin the motor of an air tool.
An air line filter can greatly increase the life of an air tool.
The filter removes dust and moisture.
Make sure all hoses and fittings are the correct size and
are tightly secured. See diagram PP1 for a typical piping
arrangement.
The tool is shipped from the factory with 3/4" NPT male inlet
thread and quick release coupling.
Diagram PP1
PLACING TOOL IN SERVICE
Accessory Installation
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool or before performing any
maintenance on this tool. Failure to do so could result
CPN: 35371111
in injury.
CPN: 85448405
For Latch Type Retainer
1. Operate the Retainer until it is approximately 90 degrees
2. Insert the accessory into the tool until the collar of the
3. Operate the Latch until it is parallel to the tool and it
15 – 20 kg (30 – 40 lbs) is the recommended amount of
downforce to apply to the tool when working. The amount
of downforce is correct when the tool hits rhythmically, is
comfortable to hold and works efficiently.
Do not repair the tool at the work site. Always take the tool
to a repair shop. Never drag the tool on the ground.
The air port and other openings will become clogged with
dirt and debris.
Compressed air is dangerous. When blowing the line clear
of dirt, wear eye protection and keep the air line directed
toward a safe, clear area.
Always blow out the air line before using to clear the line of
dirt.
Do not operate the tool unless the chisel is against the work
surface since this will cause premature wear of parts and
reduce the vibration isolation properties of the tool.
Always break material to the point of "give". Cracking does
not result in a complete break. Clear away rubble as it is
broken since uncleared rubble blocks the point of "give".
Always take the right size "bite" with the tool. When working
new material, experiment to find the right size "bite" required
for breaking that material efficiently.
If "bites" are too big, the operator will try to pry with the
tool. This could break the chisel. The tool is designed
for demolition, not prying. Always use a pick for prying.
If "bites" are to small, the operator will be working too
slowly.
If the chisel or accessory should become stuck, do not use
excessive force or mechanical means on the tool to pull out
the chisel. Doing so will damage the vibration isolation unit.
Break out the stuck chisel with a spare chisel or tool.
18
OPERATION
W A R N IN G
to the body of the tool and clicks into position.
accessory is past the Latch.
clicks into position.
N OT I C E
C AU T IO N
C AU T IO N
N OT I C E

Publicidad

loading

Este manual también es adecuado para:

Dct15bs