Scotts LHT12462S Manual Del Operario página 8

If you drop the trimmer, carefully inspect it for damage. If the blade is
bent or cracked, handles broken or if you see any other condition that
may affect the trimmer's operation, it must be repaired before putting it
back into use. Call our customer service help line at 1-800-618-7474 for
assistance.
CAUTION: Do not at any time let brake fluids, gasoline, petroleum
based products, penetrating oils, etc., come in contact with plastic parts.
They contain chemicals that can damage, weaken or destroy plastic.
Make sure the battery is detached from the unit, then use only mild soap
and a damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by a qualified
individual using only identical replacement parts.
The cutting blades are made from high quality, hardened steel and with
normal usage, they will not require re-sharpening. However, if you
accidentally hit a wire fence, stones, glass or other hard objects, you
may put a nick in the blade. There is no need to remove this nick as long
as it doesn't interfere with the movement of the blade. If it does interfere,
make sure the battery is detached from the unit and use a fine toothed
file or sharpening stone to remove the nick.
Fertilizers and other garden chemicals contain agents which greatly
accelerate the corrosion of metals Do not store the tool on or adjacent to
fertilizers or chemicals.
LUBRICATE BLADES - Stop the unit and
remove the battery pack. Then remove any
debris on blades. Apply a light machine oil
along the edge of the top and bottom blade
supports. Make sure handles remain clean and
dry.
Problem
−
Unit does not run
−
Slow running, noisy or hot blades
−
Battery will not charge
MAINTENANCE
TROUBLESHOOTING
Possible Cause
−
Battery not making contact
−
Trigger switch not operational
−
Battery not installed properly
−
Battery not charged
−
Dry, corroded blades
−
Blades or blade support bent
−
Bent or damaged teeth
−
Loose blade bolts
−
Battery not inserted into charger
−
Charger not plugged in
−
Surrounding air temperature too
hot or too cold
Model LHT12462S
Cleaning the Hedge Trimmer
■ Stop the motor and remove the battery pack.
■ Slide the blade cover over the blade.
■ Clean dirt and debris from the body of the hedge trimmer, using a damp
cloth with a mild detergent.
NOTE: Do not use any strong detergents on the plastic housing or
the handle. They can be damaged by certain aromatic oils such as
pine and lemon, and by solvents such as kerosene.
■ Moisture can cause a shock hazard. Wipe off any moisture with a soft
dry cloth.
■ Use a small brush or the air discharge of a small vacuum cleaner brush
to clear dust or debris from the air vents on the motor housing.
Storing the Hedge Trimmer
■ Remove the battery pack and store it out of the reach of children when
storing the hedge trimmer.
■ Clean the hedge trimmer thoroughly before storing. Store the hedge
trimmer in a dry, well-ventilated place that is inaccessible to children.
Keep away from corrosive agents such as garden chemicals and de-
icing salts.
■ Always place the blade cover on the cutting blades before storing.
−
Check battery is fully inserted
−
Check that lock off button is fully depressed before moving trigger
−
Check battery installation
−
Check battery charging requirements
−
Lubricate blades
−
Straighten blade or blade support
−
Straighten teeth
−
Tighten blade bolts
−
Insert battery into charger until red LED appears
−
Plug charger into a working outlet
−
Check current at receptacle by plugging in a lamp or other
appliance
−
Check to see if receptacle is connected to a light switch which
turns power off when you turn out the lights.
−
Move charger and tool to a surrounding air temperature between
39° F (4° C) and 104° F (40°C)
8
Possible Solution