Publicidad
Thin Client Installation
Read Caution Statements before setting up and operating the thin client.
Connect
Refer to the figures and proceed as follows:
1. Place the thin client on a desk, or use a Wyse-approved mounting
accessory kit.
2. Make all desired connections (video display and keyboard with mouse
are required). Connection to a 10/100/1000BaseT Ethernet network is
required unless an optional WiFi network adapter is used for wireless
connection to a network. Additional connections of peripheral devices
may be made to the other ports.
3. Connect the power adapter to the thin client power input before
connecting to a 100-240V AC, 50-60 Hz electrical outlet, and then
press the power button to apply power. When the initialization
sequence is complete, the amber activity light changes to green.
Configure
After turning on, the thin client initially goes through several boot
sequence procedures before the operating system loads. Information
about setting up your server environment is available in the thin client's
documentation.
Default User Names and Passwords
®
Microsoft
Windows
Administrator
User Name
administrator
Password
Wyse#123
User
User Name
user
Password
Wyse#123
1
For administrators, log off User desktop while holding down the Shift key until the logon box
appears.
Caution Statements
Improper connection, mounting, or use of this product could result in
component failure or undesired interference. Read the following caution
statements before setting up and operating the thin client.
Setup
•
Do not connect to AC power until all other connections (including the
power adapter) are made. Connecting or disconnecting components or
equipment on the back panel when the thin client is receiving AC power
can cause power surges and damage the device.
•
Do not force a connector into its socket. If any undue resistance is
encountered, ensure that the connector is correctly oriented to the
receptacle.
Venting and Care
•
Mount the thin client only as shown or in accordance with the
instructions provided with Wyse-approved mounting accessory kits.
Improper orientation could inhibit the dissipation of heat from the device
and damage it.
•
Allow sufficient space around the thin client for ventilation; do not place
the device in any enclosure that restricts airflow around the device; do
not place any objects on the device or block the vent outlets. Find
environmental operating specifications in the thin client's datasheet
located at:
http://www.wyse.com/products
•
For wireless usage and requirements, refer to the regulatory notices in
the thin client's documentation.
(case sensitive)
®
1
1
Embedded Standard 2009
/ 7
Power Sources
•
For regulatory compliance use only the power adapter that comes with
your device or a Wyse-approved equivalent. For proper replacement
compare the labels on both device and power adapter to ensure that
their voltages match.
Warning: Use of any other power adapter may damage your
device or the power adapter. The damage caused by an improper power
adapter is not covered by warranty.
•
Accidental loss of power can damage the thin client. Avoid connecting it
to any power outlet which can be accidentally switched off. Do not hard
reset the thin client by holding down the power button during normal
operation.
•
When turning off the thin client, be sure to perform a complete shutdown
(via the user interface or a light press on the power button). Do not
disconnect the AC power cord, DC power cord, or shut off power at a
circuit breaker (including power strips), etc., to turn off the device.
•
Surge protectors for electrical devices are recommended in areas of
lightning. However, when lightning is occurring, your equipment should
be properly shut down and unplugged from AC power until the storm
has passed.
•
Be very careful to not interrupt power while the thin client is downloading
a software update.
Battery
The thin client contains an internal button cell battery replaceable by Wyse
or one of our Authorized Service Centers. For service, visit
http://www.wyse.com/serviceandsupport/service/service.asp.
Warning: There is a risk of explosion if the battery is replaced by an
incorrect type. Always dispose of used batteries according to the
instructions accompanying the battery.
Warning: Perchlorate Materials - Special Handling May Be Required
under California Code of Regulations, title 22. (Only required within the
U.S.A.)
Need more information?
Wyse Reference Guides - User, Administrator, and related
documentation is available at:
http://www.wyse.com/manuals
Wyse-Approved Mounting Accessory Kits - Information about
approved mounting accessory kit options is available at:
http://www.wyse.com/products/accessories/mounting.asp
Wyse Service and Support - Latest software images are available at:
http://www.wyse.com/support
Wyse Device Manager - Information about Wyse remote management
software is available at:
http://www.wyse.com/products/software/devicemanager
Wyse WSM - Information about Wyse WSM software is available at:
http://www.wyse.com/products/software/wsm
Wyse and the Environment - Information about Wyse compliance with
RoHS and with the Waste Electrical and Electronic Equipment (WEEE) is
available at:
http://www.wyse.com/green
Wyse and E-Recycling - Information about recycling unwanted Wyse
product within the United States is available at:
http://www.wyse.com/about/environmental/erecycling/index.asp
Wyse Warranty Registration - Wyse's warranty registration* process is
available at:
http://www.wyse.com/serviceandsupport/register.asp
*The standard warranty is three years from the date of purchase.
3
Publicidad
