Publicidad
Idiomas disponibles
Idiomas disponibles
■
The product is not intended for use as a dental drill
or in human or veterinary medical applications.
Serious injury may result.
■
Do not grind or sand heat flammable materials.
Sparks from the wheel could ignite these materials.
■
Do not bend the flex shaft with a radius less than
13 mm. The risk of overheating will increase
substantially.
■
Ambient temperature range for tool during operation is
between 0°C and 40°C.
■
Ambient temperature range for tool storage is between
0°C and 40°C.
■
The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to
fl ow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0°C and 40°C.
■
Ambient temperature range for battery storage is
between 0°C and 20°C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■
Injury caused by thrown-off particles
–
Metal or abrasive particles may enter the eyes and
cause severe permanent damage. Wear goggles
approved for grinding operations whenever you use
the product.
■
Injury caused by vibration
–
Limit exposure. See "Risk Reduction".
■
Injury caused by dust
–
Wear appropriate dust control mask with filters
suitable for protecting against particles from the
material being worked on and abrasive particles
from the accessories. Do not eat, drink, or smoke in
the work area. Ensure adequate ventilation.
■
Injury from contact with the attachments
–
The attachment and workpiece will become hot
during use. Wear gloves when changing discs or
touching workpiece. Keep hands away from the
working area at all times. Clamp the workpiece
whenever possible.
■
Injury caused by noise
–
Prolonged exposure to noise will increase the risk
of hearing damage, and the effects are cumulative.
When using power tools for any extended period of
time, wear hearing protection.
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent
upon exposure to cold environments. Hereditary factors,
exposure to cold and dampness, diet, smoking and work
practices are all thought to contribute to the development
of the these symptoms. There are measures that can be
taken by the operator to possibly reduce the effects of
vibration:
■
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■
After each period of operation, exercise to increase
blood circulation.
■
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KNOW YOUR PRODUCT
See page 189.
1. Battery port
2. Accessory storage slots
3. Speed control dial
4. On/off switch
5. Collet nut
6. Pen holder
7. Spindle lock lever
8. Flex shaft
9. Key hole hanger
OPERATING TIPS
INSTALLING ACCESSORIES
Insert the shank of the accessory into the collet until
the shank bottoms out, then pull it out 2 mm to allow for
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English |
3
Publicidad
