Surtek GG525 Manual De Usuario página 12

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

• To prevent surging that may possibly damage
equipment do not allow engine to run out of
fuel when electrical loads are applied.
• When powering solid state equipment, a
Power Line conditioner should be used to pre-
vent possible damage to the equipment.
• Do not stick anything through ventilating
slots, even when the generator is not operat-
ing. This can damage the generator or cause
personal injury.
• Before transporting the generator in a vehi-
cle, drain all fuel to prevent leakage that may
occur.
• To avoid burns, do not touch engine muffler
or other engine or generator surfaces which
became hot during operation.
• Do not alter or modify the heat shield.
DEFINING TOTAL WATTAGE
In order to prevent overloading and possible
damage to your generator it is necessary to
know total wattage of the connected load.
To determine which load and or appliances
your generator will run follow these steps;
Check wattage requirements by referring to
the loads nameplate or by calculating it (multi-
ply amps x volts = watts).
You can get help for calculation using the
Table 1 Total the watts for each item. If the
nameplate only give volts and amps, multiply
volts x amps = watts. 1 kW = 1,000 watts.
Motorized appliances or tools require more
than their rated wattage for start up.
NOTE: Allow 2 ½ to 4 times the listed wattage
for starting equipment powered by electric
motors. The generator's rated watts should
match or exceed the total number of watts
required for the equipment you want to run.
The altitude and temperature can modify the
generator's ratings. Use the Table 2 to calcu-
late the generator's rating, multiply the factor
x rated output in the generator's specs when
the condition is not at 21ºC at the sea level.
Always connect first to the generator the
heaviest load, and then add other items one
at a time.
CAUTION: Operating voltage and fre-
quency requirements of all electronic equip-
ment should be checked prior plugging them
into this generator. Damage may result if the
equipment is not designed to operate within
+/- 10% of voltage and +/- 3 Hz of the rated
12
values marked in the generator´s nameplate.
To avoid damage, always have an additional
no solid state load plugged into the generator
if only solid state equipment (such as a televi-
sion set) is used.
A power line conditioner is recommended for
some solid state applications.
POWER USAGE (WATTS)
Load device
Air conditioner
Automatic washer
Chicken incubator
Clother dryer
Coffee maker
Electric drill (small)
Electric drill (large)
Fan
Freezer
Hot plate
Iron
Light bulb
Radio
Refrigerator
Skillet
Portable heater
Television
Toaster
Vaccum cleaner
Water pump
Water heater
Small handsaw
Large handsaw
VOLTAGE REQUIREMENTS
A power line conditioner should be used when
running one or more of the following solid
state items:
• Garage door openers.
• Kitchen appliances with digital displays.
• Televisions.
• Stereos.
• Personal computers.
• Quartz clocks.
• Copy machines.
• Telephone equipment
Other solid state equipment may require a
power line conditioner, for more information
contact customer service.
VARIATION OF RATED WATTS BY ALTITUDE
AND TEMPERATURE
Altitude
Meters
Feet
0˚C
21˚C
(32˚F)
(70˚F)
0
0
1.08
500
1640
1.02
0.95
1000
3280
0.96
0.89
1500
4920
0.91
0.84
2000
6056
0.86
0.79
3000
9840
0.75
0.71
Watt
2 000 - 3 000
150 - 1 500
100+
5 000 - 10 000
400 - 700
255 - 1 000
500 - 1000
40 - 200
300 - 500
330 - 1 100
500 - 1 500
9 - 100
50 - 200
190 - 2 000
1200
600 - 4 800
200 - 500
900 - 1 700
200 - 300
1 000 - 3 000
1 000 - 5 000
1 000 - 2 000
1 500 - 2 500
Temperatura
50˚C
75˚C
100˚C
(122˚F)
(167˚F)
(212˚F)
1
0.91
0.85
0.79
0.86
0.80
0.75
0.81
0.75
0.70
0.77
0.71
0.66
0.72
0.67
0.63
0.64
0.60
0.56

Publicidad

Tabla de contenido
loading

Productos relacionados para Surtek GG525

Tabla de contenido