Publicidad
Idiomas disponibles
Idiomas disponibles
US
To achieve efficient paper removal always gently score the areas to be stripped.
With heavily embossed, vinyl coated or painted papers this is essential. Either use a proprietary perforator tool or
alternatively score the paper with the edge of a wall scraper in a 'criss-cross' pattern with 6 inch spacing.
As with all decorating work be sure to protect carpets and furniture with covers.
SYmBOlS
CaUtiON
Steam iS HOt!
The unit is designed for safe, fast removal of wallpaper but please be aware that steam is produced at 212
protective clothing and protect your hands with heat-resistant gloves or mitts.
FilliNG:
The capacity of 4 litres (9 pints) provides approx. 105 mins (1500W) or 150 mins (1200W) steaming time before the safety cut-out
operates.
For a shorter steaming time use less water.
Screw hose onto threaded outlet of steamplate, hand-tight is sufficient. Do not over-tighten but do check for hand-tight fit from time
to time during use.
Connect mains lead from unit to power socket and switch on. lt can take up to 24 mins (approx.) before steam is produced -
depending on fill water quantity and temperature.
Do not leave unattended and keep children & pets out of the room.
Just before full steam production a small amount of bubbling and water will occur at the steamplate.
Beware of hot water discharge prior to steam emission.
StrippiNG: Remember to check a small area first.
Operation is simple for both right and left-handed people.
Simply hold the steamplate flat against the wallpaper for approx. 10 seconds. Now move the steamplate to the spot immediately next
to the one just steamed - from which the paper should now easily come away with a little help from a wall
scraper. Working this way should enable continuous paper removal although it may be necessary to steam for
longer periods with some papers, or if not completely removed first time.
Operate steamer until water level is low, then unplug unit and allow to cool for at least 2 minutes
before removing filler cap and re-filling unit.
BeWare OF Steam!
When finished, allow to cool completely and empty unit. Always store unit empty.
SaFetY CUt-OUt
A safety cut-out is fitted to prevent overheating the element if the water boils low. If unit stops boiling during use this
may be the cause. Wait for 2 minutes before removing filler cap then re-fill with water. The cut-out will self-reset and
steam be produced again within 5-15 minutes.
the cut-out will not protect the element if a part-filled unit is tilted during use in a way which enables part of
the element to be out of the water for longer than 15-20 seconds. Failure to do so can result in severe
overheating, complete element failure and void your guarantee.
textured Wall Coatings
Normally textured wall coatings can be removed using the same method as for wallpaper although the steaming time will be longer.
CaUtiON! Some textured finishes may contain asbestos which may be hazardous to health and which are subject to licensing
controls.
Vinyl Floor tiles
Vinyl floor tiles can also be removed if the steamplate is left long enough for the heat to penetrate the
adhesive. Once the adhesive is hot it softens and the tile can be peeled from the floor.
Disinfecting Soil
To disinfect soil in seed trays or greenhouses rake the soil to obtain a fine surface. Leave the steamplate
on each section, for 2 to 2 1/2 minutes which should ensure that the steam has penetrated the surface.
Killing Weeds
Steam will kill weeds on paths and patios without the use of chemicals. You will need to steam the weeds
for 1 to 1 1/2 minutes in order to kill them.
preparatiON
WarNiNG: Hot liquid or steam can burn. Danger of scalding. Steam may
also condense into boiling droplets. Steam should not be directed
towards electrical appliances. Danger of scalding appears on the cap
as either symbol.
OperatiON
Do not overfill the unit or hot water will be forced up the steam hose
OtHer USeS FOr tHe Steamplate
3
F, so be careful, wear
o
Publicidad
