Instructions For The Installation - Adeo Group PROFESSIONAL PSCHP0001 Manual De Usuario

Thank you for purchasing a ADEO's screen.
GENERAL FEATURES:
Screens manufactured by Adeo Group S.p.a. meet the following standards: 73-23 CEE and 89-336 CEE
Projection curtain made of PVC, without cadmium, fire proof class M1 e M2 (certification obtained from SNPE Centre de Recherches du Bouchet France).
Aluminium case with anti scratch paint, of white colour (other colours available on request)
UNPACK THE SCREEN:
Make sure that the screen has not been damaged during the transport check that all the accessories are inside the screen's packing
PROVISION ACCESSORIES FOR ELECTRIC SCREEN:
-screens with case: 2 mountings for ceiling and 2 for wall installation1
-screens without case: 2 side mountings
-screens with case: screws and plastic knuckle pins to lock the mountings to the screen's case
-screens without case: screws and knuckle pins
-unipolar commutator 10 A, 250 V a.c., with directional arrows and central OFF position.
-commutator box for external wall installation
-owner manual
1 the number of mountings is two for the screen sizes until 300x225 cm and three for bigger sizes.
INSTALLATION:
The screen must be installed using screws and anchors suitable for the type of wall or ceiling onto which the brackets have to be fitted.
IMPORTANT!!! AFTER FITTING THE SCREEN ON THE BRACKETS, IT IS MOST IMPORTANT TO MAKE SURE THE SCREEN IS PERFECTLY HORIZONTAL BEFORE USING.
EMPLOYMENT
It is suggested to use the screens in indoor rooms with normal condition of temperature (20-25°C) and humidity. The exposition to a temperature of more than 50°C could create permanent
damages to the planarity of the projection curtain, or the fall of it from the roller. Do not leave for long time the screen curtain exposed to the sun light to prevent the yellowing of it (check that
also as a cause of the exposition at the sun light, the screen does not reach the level of temperature above mentioned)
Because the material of which the projection curtain is made of (PVC) has the tendency of electrostatics loading, the excessive presence of dust in the projection room could create the degrade
of the optics qualities of the curtain caused from the deposit of the dust.
Do not force the cloth to come out by hand because this could cause damage to the motor or the detachment of the box containing the attachment brackets.
It is forbidden to block, impede or force the movement of the screen by grabbing on to it or swinging on it, adding or applying any object to the fabric or backdrop or modifying the structure of
the screen since it could damage the winding system with consequent property damage and injury to persons.
If you do not follow the instructions above mentioned, damages caused to the screen are not covered from warranty.
The producer is not responsible for damage to things or persons caused from mistakes in installing or using the products..
CASE: for cleaning the case you can use a soft cloth with eventually a non aggressive detergent.
PROJECTION CURTAIN: use a humid soft cloth with eventually a neutral detergent. After the cleaning it could appens that the curtain loads electrostatics, caused from the rubbing with the cloth,
it is suggested to clean the curtain with a liquid products that avoid the settling of the dust.
The installation is the same for all kind of screens, and it is different only for the presence of the case or not. For the case screen's, depending on the size, two kind of cases are used as indicated
in table below. The screens without case are formed from a roller around which there is the projection curtain rolled up, and two mountings which are needed to mount the screen on the wall or
on the ceiling.
INSTALLATION OF THE SCREENS WITH CASE: (Fig.2 and 3)
The installation could be made on the wall or on the ceiling as showed in the Fig. 2 and Fig. 3 following
WALL INSTALLATION:
insert the screw 4 into the plate 1 and screw down a little bit the nut 3 leaving 4-5 mm of slack; hook the plate to the case and fix it trough the plastic knuckle pins 2. As shown in the figures the
fixing side with the pins of the plate has to be turned to the back side of the case so the mountings are not visible, giving so a good appearance to the installed screen. we have to underline that
only for installation purposes it is the same if you mount the plate in one side or in the other because the hook's profiles of the case are perfectly symmetrical. Fix the mountings 5 with
expansion dowel which has to be suitable to the type of wall (minimum Ø 8 mm) and fix the plate 1 with mountings 5 by using ring 7 and thumb nut 3.
CEILING INSTALLATION: insert the screw 4 into the plate 1 and screw down a little bit the thumb nut 3 leaving 4-5 mm of slack; hook the plate to the case and fix it trough the plastic knuckle
pins 2. Fix the mountings on the ceiling 6, included in the screen package, with expansion dowel which has to be suitable to the type of wall (minimum Ø 8 mm), at a distance of 10 - 15 cm from
the ends of the case. For the screens with a width of more than 350 cm the third mountings has to be fixed on the centre of the case. Make the plates run 1 in the profile and positioned them in
connection with the L fluting of the mountings 6, Take care of the operation is made until the bottom of the L fitment and then tight the nut on the mounting (the nut is made with a tightness
knurling). fix the plate 1 with mountings 6 by using ring 7 and thumb nut 3.
SCREEN'S DESCRIPTION
WARNING AND CAUTION
CLEANING

INSTRUCTIONS FOR THE INSTALLATION

PROVISION ACCESSORIES FOR TURNSTILE SCREEN:
screens with case 2 mountings for ceiling and 2 for wall
installation1.
screens with case: screws and plastic knuckle pins to lock the mountings
to the screen's case
articulated joint rod
owner manual