Publicidad
Idiomas disponibles
Idiomas disponibles
PREPARATION FOR USE
LANGUAGE SELECTION
If you want to change the language of the on-screen menu, follow the proce-
dure below.
1) Connect the power cord to a standard AC outlet.
Note: If some digits appear in the corner of the screen,
press the POWER button without unplugging the power cord.
2) Press the POWER button to turn on the TV.
3) Press the MENU button so that the menu display appears
on the TV screen.
4) Press the CH(annel) ▲ or ▼ button to point to "[ENG]".
5) Select "ENG(lish)", "ESP(añol)" or "FRA(nçais)" by using
the VOL(ume) ▲ or ▼ button.
6) Press the MENU button to exit the menu.
CHANNEL PRESETTING
To preset a channel or to change a preset channel, follow the procedure below.
1) Press the POWER button to turn on the TV.
2) Press the MENU button so that the menu display appears
on the TV screen.
3) Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET".
Then press the VOL(ume) ▲ button.
4) Press the CH(annel) ▲ or ▼ button to point to "AUTO PRESET CH".
Then press the VOL(ume) ▲ button.
The tuner scans and memorizes all active channels in your area.
The TV distinguishes between standard TV channels and cable (CATV)
●
channels.
When AUTO PRESET CH action is completed, the lowest memorized
●
channel reappears on the screen.
When you press the CH(annel) ▲ or ▼ button after selecting "AUTO PRESET CH",
●
the tuner will stop at the memorized channels only.
The TV may recognize TV channels to be CATV channels by receiving conditions. In this case,
●
try AUTO PRESET CH action again after checking antenna connection.
When AUTO PRESET CH is activated where there is no TV signal input, "NO TV SIGNALS"
●
will appear on the display after the completion of channel scanning.
[ADD/DELETE FUNCTION]
1) Press the MENU button so that the menu display appears on the TV
screen.
2) Press the CH(annel) ▲ or ▼ button to point to "CHANNEL SET".
Then press the VOL(ume) ▲ button.
OPERATIONS
WATCHING A TV PROGRAM
1) Press the POWER button to turn on the TV.
2) Select the desired channel with the CH(annel) ▲ or ▼ button.
3) Adjust the volume to the desired listening level using the VOL(ume) ▲ or ▼ button.
4) Adjust picture controls for a natural looking image (see "PICTURE ADJUSTMENT").
SETTING THE SLEEP TIMER
The sleep timer function allows you to shut off the power automatically after
a set time period.
1) Press the POWER button to turn on the TV and press the SLEEP button
on the remote control.
2) You may change the sleep time by pressing the SLEEP button on the remote
control repeatedly. The timer can be set up to 90 minutes. 10 minutes each
time the SLEEP button is pressed (the timer display counts
up and sleep timer can be displayed on the screen when you
press the SLEEP button on remote control).
Note: When you disconnect the unit from the AC outlet
or when you have a power failure, the sleep time will be
lost.
CLOSED CAPTION SELECTION
You may view specially labeled (cc) TV pro-
grams, movies, news and prerecorded tapes,
etc. with either a dialogue caption or text dis-
play added to the program.
: Press the VOL(ume) ▲ or ▼ button.
PICTURE
PICTURE
CHANNEL SET
CHANNEL SET
[ENG] / ESP / FRA
[ENG] / ESP / FRA
V-CHIP SET UP
V-CHIP SET UP
CAPTION [OFF]
CAPTION [ C1]
TV SOUND [MAIN]
TV SOUND [MAIN]
AV MEMORY
This feature allows you to quickly adjust picture settings for MANUAL, SPORT, NEWS,
MOVIE and GAME to match the program you are watching.
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the VOL(ume) ▲ button so that "PICTURE" is selected.
3) Select the item with the CH(annel) ▲ or ▼ button.
Note: See "PICTURE ADJUSTMENT" to manually customize the picture.
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
ADD/DELETE
AUTO PRESET CH
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
To cancel the sleep timer:
Press the SLEEP button repeated-
ly until "SLEEP 0" is displayed.
1) Press the MENU button so that the menu
display appears on the TV screen.
2) Press the CH(annel) ▲ or ▼ button to point
to "CAPTION".
3) Press the VOL(ume) ▲ or ▼ button to
select the mode you wish.
4) When done, press the MENU button to exit
the menu.
PICTURE
PICTURE
CHANNEL SET
CHANNEL SET
[ENG] / ESP / FRA
[ENG] / ESP / FRA
V-CHIP SET UP
V-CHIP SET UP
CAPTION [ C2]
CAPTION [ T1]
TV SOUND [MAIN]
TV SOUND [MAIN]
3) Press the VOL(ume) ▲ button so that "ADD/DELETE" is selected.
4) Use the CH(annel) ▲ or ▼ button to select the channel you wish to put
into memory or to erase from memory.
Note: The menu will disappear automatically in about 10 seconds.
Perform "ADD/DELETE" function while this display appears on the
screen.
Press the VOL(ume) ▲ or ▼ button to highlight the channel number
●
in LIGHT BLUE if you wish to add the channel into memory.
Press the VOL(ume) ▲ or ▼ button to highlight the channel number
●
in LIGHT RED if you wish to erase the channel from memory.
5) Press the MENU button to exit the menu.
MTS (Multi-Channel Television Sound) SYSTEM
You can listen to a program in MTS stereo by following the steps below.
Menu
Selection
PICTURE
MAIN
Type of
CHANNEL SET
broadcast
[ENG] / ESP / FRA
Regular
-None-
V-CHIP SET UP
Stereo
CAPTION [OFF]
STEREO
broadcast
TV SOUND [MAIN]
MAIN
SAP
[To Select STEREO, MONO or SAP in Stereo broadcast]
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel) ▲ or ▼ button to point to "TV SOUND".
3) Press the VOL(ume) ▲ or ▼ button to select your desired stereo mode
([MAIN], [MONO] or [SAP]).
: Press the VOL(ume) ▲ or ▼ button.
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
RESUME FUNCTION
If the power fails or is disconnected while the TV is powered on, the TV will turn on automatical-
ly when the power resumes.
: Press the CH(annel) ▲ or ▼ button.
MANUAL
PICTURE ADJUSTMENT
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the VOL(ume) ▲ button so that "PICTURE" is selected.
3) Press the CH(annel) ▲ or ▼ button to select "MANUAL". Then, press the VOL(ume) ▲ button.
SLEEP 10
4) Select the feature you wish to adjust with the CH(annel) ▲ or ▼ button and adjust it with the
VOL(ume) ▲ or ▼ button.
BRIGHT
Adjust until the darkest parts of the picture are
as bright as you prefer.
[+] : increase brightness [-] : decrease brightness
CONTRAST
Adjust to increase or decrease contrast.
[+] : increase contrast [-] : decrease contrast
COLOR
Adjust to be brilliant or pale color.
[+] : be brilliant color [-] : be pale color
TINT
Adjust to obtain natural skin tones.
[+] : greenish tone [-] : reddish tone
SHARPNESS
Adjust to detail in the picture.
[+] : increase sharpness [-] : decrease sharpness
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
Notes:
V-CHIP SET UP
CAPTION [ T2]
"+" is achieved by pressing the VOL(ume)
●
TV SOUND [MAIN]
▲ button and "-" by pressing the
VOL(ume)▼ button.
In the preceding steps, the picture adjust-
●
ment display will disappear from the TV
screen automatically after about 10 seconds
: Press the CH(annel) ▲ or ▼ button.
[-]
[+]
BRIGHT
To show the status, press the DISPLAY
PICTURE
MONO
SAP
button on the remote control.
CHANNEL SET
[ENG] / ESP / F
-None-
-None-
SAP: Second Audio Program, which
V-CHIP SET UP
means your program can also be
MONO
CAPTION [OFF
STEREO
received in a second language or
TV SOUND [MO
sometimes a radio station.
MAIN
SAP
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MONO]
SPORT
NEWS
if you do not press any buttons.
Press the MENU and VOL(ume) ▲ button
so that "PICTURE" is selected. Press the
CH(annel) ▲ or ▼ button repeatedly until
the display returns to the screen.
If you adjust another picture control after
●
you set Game mode to [ON], Game mode
will be set to [OFF] automatically.
[USING THE GAME BUTTON]
You may also set Game mode and external
input mode at the same time by pressing the
GAME button on the remote control. "GAME"
appears on the TV screen.
To exit Game mode and external input
●
mode, press the INPUT SELECT button on
the remote control.
To cancel Game mode only, follow the steps
●
in "PICTURE ADJUSTMENT" or "AV
MEMORY". In this case, "VIDEO2" (exter-
nal input mode) appears on the TV screen.
If you press the GAME button when the TV
●
is off, the TV turns on and will be in Game
mode and external input mode automatically.
[-]
[+]
[-]
[+]
CONTRAST
COLOR
ADD/DELETE
AUTO PRESET CH
PICTURE
CHANNEL SET
[ENG] / ESP / FRA
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [SAP]
MOVIE
GAME
[-]
[+]
[-]
[+]
TINT
SHARPNESS
Publicidad
