Stiga 105 COMBI Instrucciones De Uso página 33

All manuals and user guides at all-guides.com
5. Release the belt tension as follows:
Park 2WD:
Remove the tensioner from the belt. See fig. 10.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and remove the tensioner
with your right hand. See fig. 9.
Villa, Ready:
Remove the tensioner from the belt. See fig. 11.
6. Force the belt off the machines's pulley.
7. Grip the front edge of the deck and lift up. Lift
until the deck is completely vertical and rest the
rear edge on the ground. See fig. 20.
8. Lower the deck to the ground in reverse order
after the corrective actions have been carried
out. Reset the deck according to 3.2.
5.3.2 Machines with quick connections
1. Activate the parking brake.
2. If the deck has electrical cutting height adjust-
ment, disconnect the cable from the machine.
See fig. 13.
3. Set the maximum cutting height.
4. See fig. 2. Detach the rear section of the deck on
the right and left-hand side as follows:
A. Lift up the left-hand rear section of the deck
slightly to reduce the load from the cotter pin.
B. Remove pins and washer.
C. Remove the right-hand cotter pin and washer in
the same way.
5. Set the quick connections in their rear positions.
See their supplied separate instruction.
6. Release the belt tension as follows.
Park 2WD:
Remove the tensioner from the belt. See fig. 10.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and remove the tensioner
with your right hand. See fig. 9.
Villa, Ready:
Remove the tensioner from the belt. See fig. 11.
7. Force the belt off the deck's pulley.
Check that the quick connections are in
their front positions before raising the
deck. Otherwise there is a risk of crush-
ing injuries.
8. Set the quick connections to their front posi-
tions, see separate instructions.
9. Grip the front edge of the deck and lift up. Lift
until the deck is completely vertical and rest the
rear edge on the ground. See fig. 20.
10.Lower the deck to the ground in reverse order
after the corrective actions have been carried out.
Reset the deck according to 3.3.
ENGLISH
5.4 CLEANING
The underside of the deck must be cleaned after
each use.
Set the deck in washing position.
Clean the underside of the deck carefully. Use wa-
ter and a brush.
When the surfaces are completely dry and clean,
touch up the paintwork. Use durable yellow paint
intended for metal outdoors.
5.5 BLADES
5.5.1 Safety
To reduce the risk of accidental injury in the event
of a collision and to protect important parts in the
cutting deck, a force limiter is integrated as fol-
lows.
• Shear bolts between blades and blade bar.
• Torque limiting between gear wheels and blade
shaft.
• Possibility of positive drive belt slipping on the
plastic gear wheels.
5.5.2 Replacing blades
Wear protective gloves when changing
blade(s) to avoid cutting yourself.
Check that the blades are always sharp.
This produces the best cutting results. The blades
should be replaced once a year.
Always check the blades after a collision. If the
blade system has been damaged, defective parts
should be replaced.
Always use genuine spare parts. Non-
genuine spare parts can entail a risk of
injury, even if they fit the machine.
The blades are replaceable. When replac-
ing, both blades on the same blade bar must be re-
placed to avoid imbalance.
Attention!
Note the following when reassembling:
• The blades and blade bar must be installed as in
fig 6.
• The blades can be turned 1/3 of a turn in their
mountings. Select positions so that the blades
are offset 90° from each other. See "5.5.3" be-
low.
Tightening torque:
Screws (6:P) - 45 Nm
Shear bolts (6:Q) - 9.8 Nm
In the event of a collision, the shear bolts (6:Q) can
break and the blades bend back. If this has hap-
pened, install genuine shear bolts and tighten as
above.
EN
33