Audizio 10B04H37 Manual De Instrucciones página 8

Show channel information: Press [Menu/Info] to show various forms of information regarding the station that is being played.
FM settings:
When in FM mode, press and hold [Menu/Info] to enter the settings menu. Rotate [Tune/Select] to be able to select the
following properties:
• Auto scan: Initiates an automatic scan for stations.
• Scan setting: Enables to choose between a scan for all stations, or for strong stations only.
• Audio setting: Enables to choose between stereo allowed- or forced mono playback.
• System: Identical to "System settings" menu.
• Press [Mode] to select turntable mode.
• Place the record on the turntable. If required, place the 45rpm adapter on the record spindle.
• Choose the desired playing speed using the speed selection switch (33-, 45- or 78rpm).
• Turn on the unit.
• Make sure that any protective cover is removed from the stylus.
• Unlock the tone arm by releasing the tone arm clip.
• Raise the arm by using the tone arm lever.
• Place the stylus vertically over the first track of the record, the turntable will start turning automatically.
• Lower the stylus slowly onto the record by using the tone arm lever to play.
• When a record comes to the end, the turntable will stop automatically if the auto-stop switch is in the ON position. If the
switch is in the off position then it will keep turning until the switch is set in the ON position.
* Some vinyl records stop before the end or do not stop when the end is reached. In this case set Auto-stop to OFF.
• Lift up the tone arm and put it on the rest when finished, always using the tone arm lever.
• Lock the tone arm by closing the tone arm clip.
• Re-attach the stylus cover.
• Turn off the power.
Before transmission between your BT device and the radio is possible, both devices must be coupled. This process is called
"pairing". The radio is served as a receiver, to receive the music stream to be played on the radio.
If you have already coupled to a BT device before, this connection will be restored automatically when both devices are in
range and BT operation has been selected on the radio. "Pairing" does not have to be repeated. This function may need to be
activated in your BT device, however.
• Press [Mode] until "BT" shows on the display.
• Turn on BT streaming on your device. The device will scan for pairable BT devices in the reception range.
• Select "Audizio Tulsa" from the list with found devices.
• Start playback on your BT device. Playback now takes place emitting sound from the radio.
You can listen to the music stored in other audio device or smart phone via the radio, through the connection to the 3.5 mm
aux-in jack on the front side. Use a cable with 3.5 mm pins at both ends, one end connected to the aux-in jack on the radio,
the other end connected to the earphone jack on the audio device (or line out socket if available).
Press [Mode] and select AUX mode, press [Tune/Select] to confirm and enter. Play music on the connected device, the sound
will be emitted from the radio.
Playback: Insert your USB drive or SD (TF)-card in the corresponding slot. The display will show "Please wait", then "USB" or
"TF", depending on the chosen method. The device will automatically start playing the files. Rotate [Tune/Select] to choose
the previous/next track. Press [Scan/Play] to (re)start/pause playback. Press [Preset/Repeat] to select a repeat mode (One-
All-Random).
Record:
• Insert your USB drive or SD(TF)-card in the corresponding slot.
• Press [Mode] to select the music source you want to record.
• Press [Record] until "REC" starts flashing on the display. The device will now record.
• To stop recording, press [Record] until "REC" disappears from the display.
• After recording, press [Playback] to play the recorded files from USB- or SD.
To set or change alarm 1 or 2, press and hold [Alarm]. Select either "Alarm 1 info" or "Alarm 2 info" and press [Tune/Select].
The alarm setup prompts you for the following parameters. Select a value for each parameter by rotating the [Tune/Select]
knob and press [Tune/Select] to confirm and prompt the next parameter.
• Alarm: Choose to turn the alarm on/off.
• Frequency: Daily, Weekdays, Weekends, Once.
8