EINHELL Expert TE-TC 620 U Manual De Instrucciones página 26

other part that is damaged should be care-
fully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions that may aff ect its
operation. A guard or other part that is dama-
ged should be properly repaired or replaced
by an authorized service center unless other-
wise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service center. Do not use tool
if switch does not turn it on and off .
20. Warning
– The use of any other accessory or attach-
ment other than recommended it this ope-
rating instruction or the Einhell catalog may
present a risk of personal injury.
21. Have your tool repared by an expert
– This electric appliance is in accordance with
the relevant safety rules repairing of electric
appliances may be carried out only by experts
otherwise it may cause considerable danger
for the user.
22. Connect the dust extraction device
Wherever there are facilities for fi tting a dust
extraction system, make sure it is connected
and used.
Special safety information
Caution! This tile cutting machine is designed for
wet cutting only. The machine may be operated
only with a non-segmented diamond cutting
wheel.
•
Wet hands
Never touch the electrical components of the
machine (e.g. switches) with wet hands.
•
Plug-in connections
All plug-in connections must be located in a
dry place and must not lie on the floor.
•
Cooling the cutting wheel
Make sure that the cutting wheel is cooled
with water during the complete cutting pro-
cess.
•
Dry cutting
Never carry out dry cuts with cutting wheels
designed for wet cutting.
•
Dust protection
Always wear a protective dust mask when
cutting tiles.
•
Diamond cutting wheels
Do not feed the tile into the machine any fas-
ter than the cutting wheel can cut.
•
Use only cutting wheels which are designed
for a minimum speed of 3000 min-1.
Anl_TE_TC_620_U_SPK8.indb 26 Anl_TE_TC_620_U_SPK8.indb 26
GB
•
Selecting the cutting wheel
Select the diamond cutting wheel to suit the
material you want to cut.
•
Fitting the cutting wheel
Before you install the cutting wheel, check the
spindle, the spindle nut and the fl anges for
damage, wear or a loose fi t. Replace dama-
ged or worn parts without delay.
•
Direction of rotation of the cutting wheel
Check the direction arrow on the cutting
wheel; the arrow must point in the same
direction as the direction in which the motor
shaft rotates.
•
Cutting wheel spindle
Make sure that the diameter of the hole in the
cutting wheel is the same as the diameter of
the cutting wheel spindle on the machine.
•
Cutting wheel guard
Only use the tile cutting machine with a pro-
perly fi tted and adjusted cutting wheel guard.
•
Cutting wheel speed
Do not exceed the safe operating speed of
the cutting wheel.
•
Sanding/grinding with the cutting wheel
•
Do not try to use the cutting wheel for sanding
or grinding jobs, e.g. to sand/grind the edge
of a cut tile. Also, do not use the machine for
radius cuts or round cuts.
•
This tile cutting machine is suitable only for
household use.
•
Cutting wheel stop time
After the machine has been switched off , the
cutting wheel needs 40 seconds to come to
a standstill. Wait until the cutting wheel has
stopped completely, pull the power plug out
of the socket outlet, and only then touch the
cutting wheel if necessary.
•
Avoid all contact with the rotating cutting
wheel when the machine is in operation.
•
Keep water away from electrical parts of the
tool and from persons in the work area!
•
If the power plug or the power cable are da-
maged they must be replaced either by the
manufacturer or by a service company autho-
rized by the manufacturer.
•
To comply with the requirements imposed by
the safety regulations, all technical modifica-
tions which change the equipment's charac-
teristics (e.g. speed) must be left strictly to
the manufacturer.
This appliance is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
- 26 -
08.11.12 12:50 08.11.12 12:50