Publicidad
Enlaces rápidos
EZO8*1F
EZO8*2F
EZO8*3F
INSTALLATION, CARE & USE MANUAL
Manual de Instalación, Cuidado y Utilización
Manuel d'installation/entretien/utilisation
EZO™ Series Barrier-Free Water Coolers
EZO™ La Barrera de la serie Liberta Agua Coolers
EZO™ Coolers d'Eau de Barrière-Libère de feuilleton
Model EZO8L
Page 1
0000000871 (Rev. B - 01/15)
Publicidad
Manuales relacionados para Elkay EZO8 1F Serie
Resumen de contenidos para Elkay EZO8 1F Serie
- Página 1 EZO8*1F EZO8*2F EZO8*3F INSTALLATION, CARE & USE MANUAL Manual de Instalación, Cuidado y Utilización Manuel d’installation/entretien/utilisation EZO™ Series Barrier-Free Water Coolers EZO™ La Barrera de la serie Liberta Agua Coolers EZO™ Coolers d’Eau de Barrière-Libère de feuilleton Model EZO8L Page 1 0000000871 (Rev.
- Página 2 EZO8*1F EZO8*2F EZO8*3F Uses HFC-134A refrigerant Usa refrigerante HFC-134A Utilise du fluide frigorigéne HFC-134A 14,24 Sensor Eye See FIG. 4 Adjustment screw See FIG. 3 FIG. 1 0000000871 (Rev. B - 01/15) Page 2...
- Página 3 EZO8*1F EZO8*2F EZO8*3F FIG. 2 Page 3 0000000871 (Rev. B - 01/15)
- Página 4 EZO8*1F EZO8*2F EZO8*3F HANGER BRACKETS & TRAP INSTALACIÓN DE LOS SOPORTES INSTALLATION DES SUPPORTS FIJADORES Y EL PURGADOR DE SUSPENSION ET DU SIPHON INSTALLATION Retire el soporte fijador que se encuentra conectado 1) Retirez le support de suspension fixé au dos du 1) Remove hanger bracket fastened to back of a la parte posterior del enfriador sacando un (1) refroidisseur en retirant une (1) vis.
- Página 5 EZO8*1F EZO8*2F EZO8*3F Service Instructions Lower and Upper Shroud 22 - Bubbler To access the refrigeration system and plumbing connections, remove four screws from bottom Assembly of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube.
- Página 6 EZO8*1F EZO8*2F EZO8*3F SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses (See Page 1.) Turn this screw clockwise to increase range and counterclockwise to decrease range (See Fig.
- Página 7 EZO8*1F EZO8*2F EZO8*3F Cleaning the strainer To clean the strainer, unscrew the cap of the solenoid valve. Remove screen and rinse thoroughly with water. Insert screen back into solenoid valve and screw cap on. Make sure the o-ring is placed properly. Limpieza del filtro Para limpiar el filtro, desatornille la tapa de la válvula solenoide.
- Página 8 POUR OBTENIR DES PIÈCES, CONTACTEZ VOTRE DISTRIBUTEUR LOCAL OU COMPOSEZ LE 1.800.834.4816 IMPRESO EN LOS E.E.U.U. IMPRIMÉ AUX É.-U. ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 0000000871 (Rev. B - 01/15) Page 8...