Sierra 054650-10 Instrucciones De Montaje Y Uso

EN Installation and Operating Manual
USA and Canada
Dometic Marine US Corporation
Litchfield Division
1 Sierra Place
Litchfield, IL 62056-3029
877-663-8396 (option 1)
Save these instructions for future reference, installation, and use of this product.
Specifications
Capacity 1200 lb (544 kg)
Travel 10 in.
Wheel Poly - 6 in.
1 Installation

WARNING: Crushing hazard.
Only mount this jack on a square or rectangular trailer tongue. Failure to
obey this warning could result in death or serious injury.
q
1
Attaching the handle
q Bolt
w Handle
1. Thread the bolt through the handle.
2. Secure with the lock nut.
3. Use a 13 mm socket wrench to tighten the lock nut.
4. Position the jack so that the handle clears any obstructions during cranking
and the jack can swivel freely.
q
w
2
Mounting the jack on the trailer tongue
054650-10
Service center and dealer locations
Visit: www.sierraparts.com
1500 lb (680 kg)
10 in.
Poly spoked - 6 in.
e
w
r
e Lock nut
r Swivel pin
t
r
e
Form No. 4445104150 2023-07-12 | ©2023 Sierra International LLC
Swivel Up Bolt-On Trailer Jack
Mounting plate
q
w Mounting bolt
e Lock washer and nut
5. Insert two bolts through the mounting plate above the trailer tongue and two
bolts through the mounting plate below the trailer tongue.
6. Slide the backing plates over the bolts.
7. Secure the backing plates with the lock washers and nuts.
8. Torque to 25 ft lbs (33.9 Nm).
9. Check that the handle can be cranked freely and that there is enough
clearance between the jack and the trailer coupler.
2 Operations

WARNING: Crushing hazard. Failure to obey the following warnings
could result in death or serious injury:
• Do not exceed the rated load capacity.
• Always secure the trailer from rolling when coupling or uncoupling the
trailer.
• Excessive side loading should be avoided.
• Make sure the plunger pins are properly locked into the detent holes in the
mounting plate before operating the jack.
• The jack must be secured in the folded up position before towing.
• When raising or lowering the jack, keep body, feet, and bystanders clear of
the trailer tongue.
• Not for highway use. Never tow with a load applied to the jack.
NOTICE: To minimize stress on the jack and its components, and to allow the
wheel to align with the direction of travel, always crank the jack two revolutions
above the fully down position when moving the trailer.
Trailer Jacks are engineered to vertically support the weight of a loaded trailer at
rest on hard surfaces and are intended for vehicle alignment only. Maneuvering
a loaded trailer jack, other than aligning the trailer to the hitch, or storing on soft
surfaces will introduce lateral loads on the caster and wheel which could cause
premature failure and is not covered under warranty.
1. Make sure the bolts and nuts are securely fastened before every use.
2. Pull the swivel pin out and swivel the jack into position.
I
Only swivel the jack when the trailer is coupled to the towing vehicle.
3. Make sure the swivel pin is engaged and locked.
4. Turn the handle clockwise to raise and counterclockwise to lower the jack.
I
Never overcrank the handle.
3 Maintenance
The jack is pre-greased for immediate use. The jack includes two grease ports for
lubrication as needed. We recommend Sierra Hydro Defense Marine Grease for
ultimate protection.
LIMITED ONE-YEAR WARRANTY
LIMITED 1-YEAR WARRANTY AVAILABLE AT SIERRAPARTS.COM/EN-US/
SUPPORT/WARRANTYSTATEMENTS. IF YOU HAVE QUESTIONS, OR TO OBTAIN
A COPY OF THE LIMITED WARRANTY FREE OF CHARGE, CONTACT:
DOMETIC MARINE US CORPORATION
LITCHFIELD DIVISION
1 SIERRA PLACE
LITCHFIELD, IL 62056-3029
877-663-8396 (OPTION 1)
Backing plate
r
t Trailer tongue
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov