HIKVISION UD11740B Guía Rápida

DS-PWA32-H
Wireless Security Control Panel
UD11740B
E N G L I S H
Diagram References
Appearance
1
Note: The function of GPRS or 3/4G(implemented with build-in SIM card slot) depends on the model of the device.
Power On
Arm Armed 2 6 SIM Card Slot
4 2
2 1 AC Power
/Disarm Disarmed
Power Off
2 7 Tamper Spring
System Fault 2 8 Reset Button
2 2 Fault Alarm Occurred
2 5
Alarm
No Fault Device Tampered 2 9 AP&STA Switch
No Alarm 10 2 Battery Connector
Panel is added to
2 3 Link
Hik-connect account 11 2 Network Interface
Panel is not added to 12 2 Power Interface
Hik-connect account
Note: Remove the rear cover, and some of the components and interfaces are on the rear panel.
2 Installation
1. Loosen the screw on the rear cover. Slide down the rear cover and remove it from the
control panel.
2. Insert a SIM card into the SIM card slot.
3. Connect the battery to the control panel.
4. Connect the power adapter to the control panel and a power outlet. The power indicator
turns green about 30s later, which means that the device is powered on.
Note: The condition of no SIM card, no battery, AC power off, or network disconnected, will cause Control Panel Fault.
5. Connect the Ethernet cable to an internet outlet. While the device is added to a Hik-Connect
account, the link indicator turns green.
6. Secure the rear cover in the installation position with the supplied screws. Attach the
control panel on the rear cover, and tighten the rear cover screw to complete the installation.
Side Opening
If you need to route the cable though the botton of the panel, remove the sheet of the side
opening.
TAMPER Screw
It is compulsory to secure the TAMPER screw.
Set Up
3
Set up via APP
1. Log into the App Store or Google Play and input Hik-Connect to search and install the
mobile client.
2. Log into the APP with Hi-Connect account.
3. Tap Add Device. Scan the device QR code on the rear panel(on the lable).
4. Tap Connect to a Network. Select Wireless Connection (AP) as the connection mode.
5. Push the AP/STA mode switch to the AP position, tab Confirm.
6. Tap Connect to Wi-Fi on the promt-up window. Select and connect to a stable Wi-Fi , and
click Next.
7. Create a password to activate the device.
8. Push the AP/STA mode switch to the STA position.
Note: You need to enter the Verification Code (on the device lable which is pasted on the rear panel) before
activation if you add the device by entering the device serial No.(SN).
Set up via Web Client
Log Into the Web Client
Default IP Address when using mobile broswer in the AP mode:192.168.8.1. The device must be in the AP mode.
Default IP Address when connectiing the network cable with computer directly :192.0.0.64
Input the device IP address in the address bar of the web browser. Create a password to
activate the device and log into the web client.
Add a Camera for the Zone
1. Click System-Network Camera, and you can add two cameras for the control panel.
2. Click Wireless Device-Zone, select a zone, click the Settings icon, and select a camera to link
with the zone.
You can also link a camera with the zone via APP, refer to the Wireless Security Control Panel
User Manual for details.
Configure Video-Push
You can view the alarm video via APP and email. For detailed settings, refer to Security
Control Panel User Manual.
Set up via 4200 Client
1. Download and install the iVMS-4200 client.
Note: Get the client software from the official website:www.hikvision.com.
2. Enter Device Management page, select the device in the Online Device List, click Edit
Network Settings, change the port as 80, and click Add to Client.
Note: You should activate the device for the first usage.
For multi-language switch , refer to Security Control Panel User Manual (scan the QR code) for details.
Function Button Operation
4
Note: Add card or keyfob via the web client before adding peripheral device for clearing tampering alarm.
Add Peripheral Device
While the control panel is not in the configuration mode, press the function button on the
side of the control panel once and trigger a peripheral device.
Note: Keyfobs cannot be added by function button operation.
Check RF Signal
While the control panel is not in the configuration mode, double press the function button,
and you can check the RF signal strength on the peripheral device .
Specification
Alarm Input 32
Alarm Output 32
Wireless Device
Siren 2
Connection
Keyfob 8
Partition 1
Interaction Audio Output 1, 1.5W
RF Frequency 433MHz
RF RF Modulation 2GFSK
RF Distance 800m（Open Area）
Wired Network Ethernet 10M/100M Self-adaptive
Supports report push-notification to ARC & Cloud, text
Cellular Network GPRS, 3/4G
notification via SMS, and audio notification via phone call
Standard 802.11b/g/n
Wi-Fi
Encryption Supported
Channel 2.4G
Application & Application iVMS-4200, and mobile APP
Protocol Protocol SIA - Contact ID
User User 13 (1 Installer, 1 Administrator, and 11 General User)
Power 5 VDC，10W
Consumption (without HDD) <5.6W
Operation Temperature –10℃ to 55℃
Others
Operation Humidity 10% to 90%
Shell Material PC+ABS
Dimension(WxHxD) 155 x155x35mm
1
1 2 2 2 2 3 4 2 5 2
2 6
2 7
2 8
2 9
2
2 4 2 5
Cable Pipe
Cable Pipe Cable Pipe
3
Components
Control Panel x 1
2
2 1
2
10
11 2
12 2
2 6
Cable Pipe
2 2 2 7
Battery x 1
2 2
Product Information
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital
Technology Co., Ltd. or its subsidiaries (hereinafter referred to be "Hikvision"). This user manual (hereinafter referred to be "the
Manual") cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties, guarantees or representations,
express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to the Axiom Security Control Panel Kit.
The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter
are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to
firmware updates or other reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement and other Hikvision's trademarks and logos are the properties of Hikvision in
various jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.
Power Adapter x 1 Screw x 4
2 3
Tear off
4
Quick Start Guide x1