Publicidad
Idiomas disponibles
Idiomas disponibles
failure tO OBserVe these Warnings cOuld result in inJury
this
instructiOn
iMpOrtant safety infOrMatiOn.
read this instructiOn Manual carefully
and understand all infOrMatiOn BefOre
Operating this tOOl.
• Always operate, inspect and maintain this tool in
accordance
Institute Safety Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety codes
and regulations.
• For safety, top performance and maximum durability
of parts, operate this tool at 90 psig; 6.2 bar max
air pressure with 1/4" diameter air supply hose.
• Always
wear
protection
maintenance on this tool.
• Always wear hearing protection when using this
tool. High sound levels can cause permanent hearing
loss. Use hearing protection as recommended by
your employer or OSHA regulation.
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and
power of this tool.
• Air powered tools can vibrate during use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your
hands and arms. Discontinue use of tool if discomfort,
tingling, or pain occurs. Seek medical advice before
resuming use.
• Compressed air can cause severe injury. Never
direct air at yourself or others. Always turn off the
air supply, drain hose of air pressure and detach tool
from air supply before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool. Failure to
do so could result in injury. Whip hoses can cause
serious injury. Always check for damaged, frayed
or loose hoses and fittings, and replace immediately.
Do not use quick detach couplings at tool. See
instructions for correct set-up.
OperatiOn
For best results, hold the tool firmly by the knurled portion of
the nose (2) and at a natural angle to the working surface, much
as one would hold a pencil. Open the throttle valve (3) fully
by holding the throttle valve (3) securely and turning the tool
clockwise until the tool stops. This will provide maximum power
at the impact point. NOTE: Do not force the tool as this might
damage internal o-rings. The impact force may be adjusted
for various surfaces by holding securely the throttle valve and
SE160
SE160 Air Engraving Pen
WARNING
Manual
cOntains
with American
National
impact-resistant
eye
and
when
operating
or
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
Standards
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Tool shaft may continue to rotate briefly after throttle is
released. Avoid direct contact with accessories during and
after use. Gloves will reduce the risk of cuts or burns
face
• Keep away from engraving tip of tool. Do not wear
performing
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
• Use only accessories recommended by Matco Tools.
• Do not lubricate tools with flammable or volatile liquids
such as kerosene, diesel or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
turning the tool counterclockwise towards the OFF position. The
tool comes with an engraving needle for a thick plate. To replace
needle, secure the body (1) in a vise fitted with soft jaws and
unscrew nose (2). Using a rubber hammer, tap out needle guide
(6) and replace the needle as desired.
Lubricate pen daily, or each time used, using a light mineral oil,
free from acids, carbon or gummy residue. It is recommended
that the lubricant used has a viscosity of 1.7 + 3.3E/50ºC
(122ºF).
2
06/13/12
Publicidad
