Publicidad
12 | English
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Hold the power tool securely. When tightening and
u
loosening screws be prepared for temporarily high torque
reactions.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The machine is intended for driving in and loosening screws
and bolts as well as for tightening and loosening nuts within
the respective range of dimension.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Tool holder
(2)
Locking sleeve
1 609 92A 4JH | (24.11.2020)
(3)
"PowerLight" lamp
(4)
Carrying strap lug
a)
(5)
Battery release button
a)
(6)
Battery
(7)
Rotational direction switch
(8)
On/off switch
(9)
Battery charge indicator
(10) Handle (insulated gripping surface)
a)
(11) Universal bit holder
a)
(12) Screwdriver bit
(13) Screwdriver bit with ball catch
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless Impact Wrench
Article number
Rated voltage
No-load speed
Impact rate
Maximum torque, hard
screwdriving application ac-
cording to ISO 5393
Machine screw diameter
Max. screw diameter
Tool holder
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
A)
ure during operation
and
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Limited performance at temperatures <0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 87 dB(A); sound power level
98 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
a)
GDR 12V-105
3 601 JA6 9..
V=
12
-1
min
0–2600
-1
min
3100
Nm
105
mm
M4–M12
mm
8
¼" internal
hexagon
kg
1.0–1.2
°C
0 to +35
°C
–20 to +50
GBA 12V...
GAL 12...
GAX 18...
Bosch Power Tools
Publicidad
