Publicidad
Idiomas disponibles
Idiomas disponibles
Safety Information
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
UK DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB,
SE-105 23 STOCKHOLM SWEDEN, declare
under our sole responsibility that the product
(with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
S.I. 2012/3032, S.I. 2017/1206
Designated Standards applied:
EN 301 489-33 V2.2.0, EN 301489-1 V2.2.0,
EN 302 065-2 V2.1.1, EN 62368-1:2014
Authorities can request relevant technical information from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 2 May 2022
Carl von Schantz, Managing Director
Signature of issuer
Authorised Representative UK:
Atlas Copco Ltd
Swallowdale Lane
Hemel Hempstead
Hertfordshire HP2 7EA
RF Exposure Statement
This portable transmitter has been tested and found to comply
with FCC General Population RF Radiation Exposure limits
set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. The antenna used
for this device must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
Information regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
4
© Atlas Copco Industrial Technique AB - 9834 5353 00
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that certain
electrical components in the product may contain lead metal.
This is in compliance with current substance restriction legis-
lation and based on legit exemptions in the RoHS Directive
(2011/65/EU). Lead metal will not leak or mutate from the
product during normal use and the concentration of lead metal
in the complete product is well below the applicable threshold
limit. Please consider local requirements on the disposal of
lead at product end of life.
Regional Requirements
WARNING
This product can expose you to chemicals including lead,
which is known to the State of California to cause cancer
and birth defects or other reproductive harm. For more
information go to
https://www.p65warnings.ca.gov/
Safety
DO NOT DISCARD - GIVE TO USER
WARNING Read all safety warnings, instructions, il-
lustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may result
in electric shock, fire, and/or serious injury.
Save all warnings and instructions for future refer-
ence.
WARNING All locally legislated safety rules regard-
ing installation, operation and maintenance shall be
respected at all times.
Statement of Use
• For professional use only.
• This product and its accessories must not be modified in
any way.
• Do not use this product if it has been damaged.
• If the product data or hazard warning signs on the product
cease to be legible or become detached, replace without
delay.
• The product must only be installed, operated and serviced
by qualified personnel in an industrial environment.
Product Specific Instructions
Service and Maintenance
Preventing ESD Problems
The components inside the product and controller are sensi-
tive to electrostatic discharge. To avoid future malfunction,
make sure that service and maintenance is carried out in an
ESD approved work environment. The figure below shows an
example of an appropriate service work station.
ILT Tag
Publicidad
