Publicidad
Idiomas disponibles
Idiomas disponibles
Press the 'INFO/MENU' button to exit to the main screen.
• DRC
DRC or Dynamic Range Compression is a feature that some DAB stations
use. This enables the audio to be evened out by raising the volume of the
quieter audio levels and lowering the volume of the louder audio levels.
Option contains DRC off/DRC low/DRC high
• Prune
You can remove DAB stations from the radio that are listed with a '?' in
front of their name by using the prune function.
Once you've selected a station you wish to remove, select 'Prune', from
the menu options. You will be presented with the choice 'Yes' or 'No'.
Select 'Yes' to remove the station. Use the tune +/- buttons to go through
the options and press the dial to confirm.
• Preset
The preset stores favorite stations for easy access, our DAB module has
up to 30 preset memories.
To store a station to preset list
Press and hold PRESET key until the display shows Preset Store. Use
NEXT/PREV key to select a preset, then press SELECT key to store
currently-playing station.
• To recall a station
Short press PRESET key, the display shows Preset Recall. Use
NEXT/PREV key to select one of the listed station and press SELECT key
to play.
FM Mode
• Select FM Mode
Press MODE key and choose the FM mode, press "OK" key confirm.
• Auto Tune FM
To auto tune to the next available radio station press and hold either Tune
+/-' buttons for 3 seconds. This will start the FM auto scan.
'+' will scan up the channel and will scan down the channel.
The scan will always stop at the next signal received. Save as a preset if
required
• Manually Tune FM
Press either 'Tune +/-' buttons to manually tune the radio in FM mode. This
helps in poor signal areas to get a clear signal.
Save as a preset if required
FM Options
• FM Menu Options
Press and hold the 'Info/Menu' button until you see 'Scan Setting'.
Press the tune +/- buttons to cycle the options and press the dial to select.
The options here are:
Auto Scan > Scan Setting >Audio setting > Preset > System
• Auto Scan
Press Auto SCAN key to scan through the FM band frequencies, and the
stations found are stored in the preset list sorted by frequency.
• Scan Settings
Select 'Scan Settings' from the menu options,
Press the tune +/- buttons to cycle between either 'Strong Stations only' or
'AII Stations', Press the dial to select the required option.
The asterisk in the top right corner indicates current selection.
You will be sent to the previous menu once a selection has been made.
Press the Info/Menu" button to return to the main screen.
• Audio Settings
Select 'Audio setting' from the menu option,
You can change the sound output from stereo to mono with this option.
Then Press the tune +/- buttons to chose from 'Stereo allowed' and'
Forced Mono' options and press the dial to confirm. The asterisk in the top
right corner indicates which option is currently in use.
• Presets
Our mould has up to 30 preset memories for FM, which works in the same
way as DAB mode presets.
Bluetooth Mode
• Select Bluetooth Mode
To select Bluetooth, press "Mode" repeatedly until the Bluetooth icon
appears on the display
• Pairing
The radio is automatically in pairing mode and show 'Disconnected' on the
display.
Activate the bluetooth on your device and search for available devices.
Look for and add "RADIO" The radio will automatically pair with the device
and no code is required. The display will show "Connected' if the pairing
is successful.
• Using Bluetooth
Press Okay/Pause key to control music playback or pause.
Press PREV/NEXT key to select the previous/next song to play,
The volume is controlled in the normal way by turning the dial.
System Options
• System Menu Options
Press and hold the 'Info/Menu' button until you see either
'Scan Setting' in FM mode or Tull Scan' in DAB+ mode. Press the tune +/-
button to cycle through the options until you get to 'System' then press the
dial to select it.
The options here are:
Time> Alarm > Language> Backlight> Sleep> EQ> Reset > SW Ver.
• Time
All the time and date functions and preferences can be altered here.
1. Set Time/Date
With this option you can manually set the time and date.
Once selected from the 'Time' sub menu you will see the hours flashing.
Press the tune +/- buttons to cycle through the hours and press it to select
the required hour value. Once the hour has been set you will have the
minutes flashing. Repeat the process for choosing the hour for the
minutes. Once selected you will move on to the next screen for setting the
date. Similar to setting the hour and minute, you cycle through the
numbers with the tune +/- buttons and press the dial to select your chosen
value, and then move to the next value to set. When the last value is set
the display will confirm that the new time and date has been saved.2.Auto
update, Update from Any/ Update from DAB/Update from FM / No Update
2. Set 12/24 hour, Set 12 hour/ Set 24 hour
3. Set date format, MM-DD-YYYY/ DD-MM-YYYY
• Alarm
Wake-up alarms with snooze facility, at the set time, quietly at first, then
gradually building up to the set
volume.
Alarm > Frequency>Wake up time> Source >Duration>Volume
1.The alarm setting Menu options include:
- Alarm: Off /On
- Frequency: daily/once/weekends/weekdays
- Wake up time: hours and minutes
- Source: Buzzer/DAB/FM
- Duration:15/30/45/ 60 /90/120 minutes
- Volume
2.Alarm ring up
- Press STANDBY key to switch the alarms off.
- Press SELECT key to temporarily silence a sounding alarm, alarm will
trigger again after a snooze period.
• Language
With this option you can choose what language the radio uses to display
the menu options in.
The language options available are： English, Polski, Deutsch, Francais,
Slovensky jazyk, Cesky Jazyk, Limba Romans, Magyar nyelv, Lietuviu
kalba, Latviesu valoda.
Cycle through the options with the tune +/- buttons and press the dial to
select an option. The asterisk in the top right corner indicates current
selection.
• Backlight
Setting the backlight brightness of the display, option contains Low /
Medium/ High.
Timeout> On level > Dim level
Time Out
This is to set the duration of time before the display dims. Choose from the
options by turning the dial and pressing it to select:
On > 10 > 20 > 30 > 45 > 60 > 90 > 120 > 180 (Seconds)
The asterisk in the top right corner indicates current selection.
• On Level
This option lets you set the active display light level.
Choose from the options by turning the dial and pressing it to select:
High > Med > Low
The asterisk in the top right corner indicates current selection.
Dim
This option lets you set the inactive display light level.
Choose from the options by turning the dial and pressing it to select:
High > Med > Low
The asterisk in the top right corner indicates current selection.
• Sleep
You can set the length of time the radio is on for with this feature.
Once selected from the system options you with have access to
• EQ
You can change the sound output preference with this feature.
7
Publicidad
