Publicidad
Idiomas disponibles
Idiomas disponibles
9. OFF-SEASON STORAGE
If the Pool Cleaner will not be in use for an extended period of time, perform the following storage steps:
• Make sure that no water is left in the Pool Cleaner
• Thoroughly clean the filter basket and panels/canister and insert in place
• Roll up the cable so that it has no kinks
• Store the Pool Cleaner in a protected area out of direct sun / rain / frost, at a temperature of between
5°-45°C / 41°-113°F
10. TROUBLESHOOTING
If the suggested solutions do not solve the problem, please contact your dealer or Service Center.
Symptom
Possible reason
The power-supply
• No voltage in the power socket in the wall.
or its switch led
• The power supply is not switched ON.
are not working.
• The power cable is not well connected
into the power supply inlet.
The Pool Cleaner
• The floating cable is not well connected
does not move.
into the power supply outlet.
• An obstacle blocks the impeller,
tracks or wheels.
The Pool Cleaner
• Clogged filter basket/canister.
is moving in
• Debris stuck in the impeller-house or
circles.
impeller-cover.
• Power supply incorrectly positioned.
• Algae or pool water is out of Spec.
The Pool Cleaner
• Debris stuck in the impeller-house
does not turn
or impeller-cover.
or moves in one
direction only.
The Pool Cleaner
• Clogged filter basket/canister.
moves but does
• Debris stuck in the impeller-house or
not clean the
impeller-cover.
pool.
The Pool Cleaner
• Power supply incorrectly positioned.
cleans only part
of the pool.
• Not enough floating is released for the
correct operation of the Pool Cleaner.
The floating cable
• Clogged filter basket/canister.
has kinks.
• Debris stuck in the impeller-house or
impeller-cover.
The Pool Cleaner
• Clogged filter basket/canister.
doesn't climb
• Algae on walls.
the walls.
• Unsuitable pH level.
• Debris stuck in the impeller-house or
impeller-cover.
Robotic Pool Cleaner Mass 12
Corrective action
• Check that there is voltage in the power socket in the wall.
• Check that the power supply is plugged in and turned ON.
• Check that the power cable is securely connected all the way
• Turn the power supply off. Wait 30 seconds then turn it back on.
• Check that the floating cable is securely connected all the way
• Unplug the power supply. Open the impeller cover
• Clean the filter basket/canister.
• Remove debris stuck in the impeller-house or impeller-cover
• Place power supply in a position so that the Pool Cleaner
• Correct pool and water conditions.
• Remove debris stuck in the impeller-house or impeller-cover
• Clean the filter basket/canister.
• Remove debris stuck in the impeller-house or impeller-cover
• Place the power supply in a position so that the Pool Cleaner
• Check that there is enough slack in the floating cable
• Clean the filter basket/canister.
• Clean the filter basket/canister.
• Remove debris stuck in the impeller-house or impeller-cover
• To remove the kinks, stretch the floating cable out completely
• Clean the filter basket/canister.
• Check the level of the chemicals of the water. Improper levels
• Remove debris stuck in the impeller-house or impeller-cover
User Instructions
|
into the power supply.
into the power supply.
and check that nothing is trapped in the impeller.
Verify that nothing blocks the tracks or wheels.
(according to the drawings).
can freely reach all the pool area.
(according to the drawings).
(according to the drawings).
can freely reach all the pool area.
for the Pool Cleaner to reach all of the pool.
(according to the drawings).
and let it sit for at least a day in the sun.
may allow the growth of algae making the walls slippery.
If so, adjust the levels and scrub the walls.
(according to the drawings).
11
Publicidad
