Descargar Imprimir esta página
Craftsman 139.53786 Guia De Inicio Rapido
Craftsman 139.53786 Guia De Inicio Rapido

Craftsman 139.53786 Guia De Inicio Rapido

Control de luz de enchufe

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Model 139.53786 Plug-In Light Control
Modelo 139.53786 Control de luz de enchufe
Light Control Actuator
Actuador de control de luz
Antenna
Antena
Learn Button
Botón "APRENDER" (Learn)
PLUG-IN LIGHT CONTROL
The Plug-In Light Control is designed to operate lights
according to the rating chart shown. Please read the
instructions and power limitations carefully to ensure proper use
and maximum safety. DO NOT use this control to attempt to
operate toasters, coffee pots, or fluorescent lighting systems.
This Light Control can be operated by Craftsman Model 53000
Series portable remote controls and Keyless Entries.
PROGRAMMING THE CONTROL
The Plug-In Light Control receiver needs to learn the hand-
held remote code. Follow the instructions below:
• Plug the light control into a 120Vac polarized outlet. The plug
contacts are designed for polarized outlets only.
• Press and release the "learn" button on
the Plug-In Light Control. The learn
indicator light will glow steadily for 30
seconds.
• Within 30 seconds, press and hold the
button on the hand-held remote.
• Release the remote control push button. Code setting is now
complete.
The remote control push button must be held down until the
receiver indicator light flashes for the light control to learn the
remote control's code.
Learn Indicator Light
Luz indicadora de aprendizaje
Select a
push button
WARNING
To prevent possible SERIOUS INJURY or DEATH from electrocution
or fire, the light control is ONLY for indoor use.
CAUTION
ADVERTENCIA
ADVERTENCIA
Para prevenir LESIONES GRAVES O LA MUERTE posibles de
electrocución o incendio, el control de luz es para uso interior
SOLAMENTE.
AVERTISSEMENT
ATTENTION
ERASING CODES
If the receiver LEARN button is pressed and held until the
yellow indicator light alongside goes out (in about 6 seconds), all
memorized codes will be erased.
OPERATING INSTRUCTIONS
If two or more plug-in light controls are installed, they must be
located at least 10 feet apart to prevent electronic interference.
• First, plug the lamp into a wall outlet and turn it ON.
• With the lamp still in the ON position, plug it into polarized
outlet on the light control. Plug the Light Control into a 120Vac
polarized outlet. The bulb will not light.
• TO TEST: Press and release the light control actuator. The
light should turn ON. Press the remote control push button.
The light should turn OFF.
If the remote control does not activate the light, check to be sure:
• You are pressing the remote control push button selected to
operate the light control.
• The remote control battery has power. Refer to the remote
control instructions for battery changing information.
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or
modifications of this receiver and/or transmitter are prohibited, except for changing the
code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Resistive Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Amps
Motor Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/3 HP
Incandescent Lamp . . . . . . . . . . . . . . . . . . . . . . . .600 Watts
RATING
A
PR

Publicidad

loading

Resumen de contenidos para Craftsman 139.53786

  • Página 1 DO NOT use this control to attempt to operate toasters, coffee pots, or fluorescent lighting systems. OPERATING INSTRUCTIONS This Light Control can be operated by Craftsman Model 53000 If two or more plug-in light controls are installed, they must be Series portable remote controls and Keyless Entries.
  • Página 2 Este control de luz puede operarse por los controles remotos portátiles estar ubicados separados por 10 pies por lo menos para prevenir la de serie del Modelo 53000 de Craftsman y las entradas sin tecla. interferencia electrónica. • Primero, enchufe la lámpara a un tomacorrientes de pared y COMO PROGRAMAR EL CONTROL ENCIENDA.