Publicidad
Idiomas disponibles
Idiomas disponibles
In order to iden�fy these elements,
check the type plate and contact
your gas distributor.
A flexible tube and a pressure
regulator must be used for the
connec�on of this device. Contact
your gas distributor.
Working descrip�on
Depending on the model, your
space heater may be fi�ed with the
following elements:
1 – Key to start-up, light and select
the power of the device.
2 – Protec�ve screen guard.
3 – Blue flame burner.
4 – Pilot light window.
5 – Back panel.
6 – Fi�ng lugs for back panel.
7 – Gas feed coupling.
8 – Wheels for transport.
Heater start-up
Once the space heater has been
taken out of its packaging:
Remove the back panel from the
device.
Connect the flexible tube to the gas
inlet coupling of the space heater
and to the regulator, ensuring a
gas�ght fit with the collar-clips well
screwed down. Avoid twis�ng the
flexible tube.
Place the gas cylinder on the base
of the space heater and fit the
regulator to the cylinder. A�er
opening the regulator, check that
there are no gas leaks by applying
soapy water with a paintbrush to
the union of the flexible tube with
the space heater and the regulator.
Fit the back panel using the
a�ached fixing lugs (fig.3).
CAUTION: For their own safety,
keep the package (cardboard,
Styrofoam, plas�c bags, etc.) away
from your children.
Note: the replacement of the
cylinder should be carried out in a
non-flammable environment.
The space heater includes a safety
device, which turns the device off
and ex�nguishes the pilot flame
if the ven�la�on in the premises is
insufficient or the concentra�on of
CO2
exceeds
the
s�pulated by law.
It is usual for this device to operate
in very small premises.
If the flame does go out, ven�late
the room well and wait a few
minutes before reigni�ng the
space heater.
Igni�on instruc�ons
A�en�on: before using the space
heater for the first �me and a�er
long periods of non-use, we
recommend switching on the
control bu�ons several �mes
alternately and without gas flow in
order to facilitate its opera�on.
The space heater can be regulated
to three different heat intensi�es:
MAXIMUM,
MEDIUM
MINIMUM.
The
mechanism is piezo-operated.
Open the gas outlet by rota�ng the
lever on the regulator to the
correct posi�on (fig.2).
Turning on the space heater
Press the bu�on and rotate it to
your le�, holding it down for 20
seconds. Repeat this procedure
several �mes if necessary, un�l the
pilot light ignites near the bo�om
part of the protec�ve screen guard
(where the spark is seen), fig.4 and
keep pressing the bu�on for 10
seconds. If, on releasing the
bu�on, the flame goes out, please
repeat the whole procedure.
3
For MINIMUM heat – rotate the
bu�on to
For MEDIUM heat – rotate the
bu�on to
For MAXIMUM heat – rotate the
bu�on to
maximum
If any anomaly is observed or spare
parts are required, contact our
Technical Service.
The periodical maintenance must
be carried out exclusively by an
authorized technician.
We would recommend that you
hace a service carried out annually
by an authorizes technician.
Watch the pilot light, which should
be stable.
Check to see if it is necessary to
change the flexible gas tube. If it
proves necessary, obtain a new
tube and connect it as explained in
"Heater start-up".
It is recommended that the
and
cleaning of the space heater be
igni�on
carried out with the gas regulator
closed and the heater completely
cold, with nonabrasive products.
The user must wear protec�ve
gloves to clean the heater.
When the space heater is not in
use, we recommend storing it in a
dust-free atmosphere, protected
with a cloth or plas�c cover in a dry
place.
All our space heaters have been
me�culously
leaving the factory. Nevertheless, if
any
remember that our extensive
Technical Service network is at
your disposal. You should read the
sec�on "Before calling in Technical
Maintenance
Warranty
checked
before
anomaly
is
observed
Publicidad
