turboblender T20 Manual De Instrucciones página 2

CARE AND CLEANING
1. Always unplug the blender from the wall outlet before
Clean it
2. Clean the machine and its parts after use.
3. The outer cover can be cleaned with a damp cloth.
4. Always wash the carafe after use. Do not use cleaning agents
Brushes or hard bristles to clean the engine
Blender jar, because it dulls or scratches the surface.
5. In case of sediment joining the blades as a consequence
Of its use. This affects the leaves, so make sure you
Clean them for proper operation.
6. Blender must be clean and dry before storing.
7. Unplug the machine when not in use for periods
And keep it in places beyond the reach of insects, the
Moisture and dust.
8. Do not wash the blender jar or its lid in the dishwasher.
POSSIBLE PROBLEMS
POSSIBLE CAUSE SOLUTION
PROBLEM
Plug in correct
No power connection
power outlet
Blender fails
Allow motor to cool
to run
Motor overheat
down with power
protector was tripped
off in cool spot
The machine is not Place the machine
on a level surface on a level surface
The blender jug has
Increased
Make sure the blender
vibration not been placed on
jug is placed securely
the base completely
and noise
Decrease the
Container is too full
ingredients
Water or liquid Decrease the
is too high water or liquid
Leaking
from lid
The lid is not Place the lid tightly
fitted properly on the blender jug
If the problem is still not resolved, please contact your local
Distributor for maintenance.
PACKAGE CONTENTS
ENGINE PLASTIC LID OF DOSING
STICK MANUAL
BASE JAR THE JAR CAP
1 1 1 1 1 1
Manual & Warranty
1
2
3
4
5
6
10
14 13
11
8
12
7
9
REFERENCE
1 Fill cap 8 Push Button
2 Black lid 9 Stirrer ,mixer
3 10
Plastic jar Centering pad
4 Blades assembly 11 Button ON/OFF
5 Retainer Nut 12 Variable Speed
6 13
Drive socket Timer
7 14
Fuse Display
TECHNICAL PARAMETERS
Rated Voltage 220-240V Power 2200W
Nominal Frecuency Speed
50-60Hz 35.000 RPM
INSTALLATION
1. Check that the voltage is the same as indicated on the
Characteristics rating plate of your blender.
2. Check that all switches are "OFF" or "0"
3. Place the blender on a firm surface and plug into the receptacle
correctly.
4. Check that the carafe, the cap (of the carafe) and the dosing cap
are clean and prepare the ingredients before your operation.
INSERTION OF INGREDIENTS
1.Insert material into the jar
A) Place soft ingredients and liquids first, then Hard foods or ice.
Those large ingredients should be Sliced or chopped before being
added to the jar to obtain best results.
B) You should start with most ingredients in one Low speed and
increase gradually until reaching the speed medium or high, or
should start with the timer. If the ingredients
Clogged, you can press "PULSE" two or three times to reset the
operation. Put the lid on the carafe and adjust.
2. Place the Jug on the motor base correctly.
FUNCTIONING
1. Maintain safe distance between operator and machine
(Approximately 20Cm) when you start to operate.
2. Turn the power switch to ON.
3. Choose the low or high speed to put the unit in after turning it on.
4. Turn the power switch to OFF to turn off the machine.
After the maximum operating time is reached at a high speed of 5
minutes,You should go through 1 minute.
PRECAUTIONS
Do not insert metal objects such as knives, forks, spoons,etc. To
reduce the risk of cuts, do not wash the blender by hand. Check that
the vessel is correctly attached to the engine base before use the
blender.
1. Hold the container before starting as the engine is powerful.Also
check that the lanyard / cap is in place.
2. Do not place your fingers inside the jar under any
circumstances,Whether or not it is in the base of the motor, due to
the edge of its blades.
3. Remove the carafe from its base before serving the liquefied
product.
4. Do not touch the switch once the machine has started to function.
5. Unplug the power cord from the wall outlet whenUsed.
6. The lid can only be opened when the blades have stopped
rotating.
7. Unplug the machine before cleaning. The jug can be
washedseparately.
8. Do not immerse the blender motor base in the water or insert it
into theIn the dishwasher.
9. Keep the blender out of the reach of children to prevent accidents,
especially when operating.