EINHELL 4514137 Manual De Instrucciones página 11

3. Intended use
This equipment is designed to illuminate dark
areas.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
4. Technical data
Power supply: ..................................120V ~ 60 Hz
Battery voltage: ................................... 18V
Number of LED: ............................................... 20
Lumens: ........................................ 2000 lm (20W)
Weight (Tool only): .....................................2.9 lbs
5. Operation
5.1 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
5.2 Installing the battery (Fig. 4)
Press the push lock button of the battery as
shown in Fig. 4 and slide the battery into the
mount provided. Make sure that the push lock
button engages properly. To remove the battery,
follow the steps in reverse order.
5.3 On/Off switch (Fig. 3 / item 3)
Warning: Do not look into the light beam.
Switching on:
•
Press the On/Off switch (3).
•
For safety reasons, the LED work light will
always come on in its lowest brightness
setting.
Switching off :
•
Press the On/Off switch (3) again.
Anl_TE_CL_18_2000_Li_AC_USA_SPK7.indb 11 Anl_TE_CL_18_2000_Li_AC_USA_SPK7.indb 11
EN
5.4 Adjusting the brightness (Fig. 3/ item 4)
Warning: Do not look into the light beam.
•
Three different brightness settings are
available so that the LED work light can be
adjusted to the particular lighting conditions.
•
For safety reasons, the LED work light will
always come on in its lowest brightness
setting.
•
To increase the brightness, press the
brightness control (4).
•
The brightness increases to the next level
every time you press the button.
•
The current brightness setting is displayed by
the brightness indicator (5).
5.5 Adjusting the LED work light position
•
You can set the LED work light to any position
by rotating the head.
•
To do this, undo the lock knob (6) on the right-
hand side of the LED work light.
•
Then adjust the LED work light to the required
position and retighten the lock knob (6).
5.6 Operation with the 120V power adapter
(9)
•
The LED work light can also be used in
conventional fashion with the included power
adapter (9).
•
Check that your power supply voltage is the
same as the one marked on the rating plate.
•
Plug the power adapter plug (9.1) into the
socket outlet.
•
Then connect the connector (9.2) into the
power adapter connection (7) of the LED
work light.
Note: You do not need to take out the battery
when you are operating the LED work light
with the power adapter.
Note: The battery will not be charged when
you are operating the LED work light with the
power adapter.
5.7 Fastening the LED work light
The LED work light can be fastened quickly and
easily in various ways via the diff erent cutouts on
the bottom of the base.
•
Hook (Fig. 6 / item 11): The hook can be used
for quick and easy attachment of the LED
work light to e.g. a railing or scaffolding.
•
Sawtooth (Fig. 7 / item 12): The sawtooth
cutout can be used to hang the lamp to a nail
or similar. The fine tooth spacing allows the
- 11 -
15.06.2023 11:16:23 15.06.2023 11:16:23