Anker SOLIX MI80 Puesta En Servicio página 7

4. For your privacy and security, the microinverter will automatically turn off Bluetooth after
commissioning is finished. You can turn on the microinverter's Bluetooth again by disconnecting and
reconnecting the DC wires. Follow the above steps to complete commissioning within 15 minutes.
LED Guide
When sufficient DC voltage from the module is applied, the microinverter will be powered, and the LED will start flashing.
LED Indicator Description
DC power is first applied to the microinverter,
Ten Short Green Flashes
the startup is successful.
Flashing Green Every 5 Seconds Producing power.
The microinverter is in protection status or
Flashing Red Every 5 Seconds
disconnected from the grid.
Ground Fault Detector Interrupter (GFDI)
Steady Red
error in the PV system is detected.
Specifications
Microinverter
Model
Recommended PV Module Power (STC) Range
Peak Power Tracking Voltage
Operating Voltage Range
Input Data (DC)
Maximum Input Voltage
Maximum Input Current
Isc PV
Maximum Continuous Output Power
Nominal Output Voltage / Range (1)
Output Data (AC)
Nominal Output Current
Nominal Output Frequency / Range (1)
Power Factor
Peak Efficiency
Efficiency Nominal MPPT Efficiency
Night Power Consumption
Operating Ambient Temperature Range (2)
Storage Temperature Range
Dimensions (W × H × D)
Mechanical Data Weight
DC Connector Type
Cooling
Enclosure Environmental Rating
09 EN
How To
Follow the instructions to start the
configuration.
The system is working.
Check if the AC input of the micro
inverter is normal. If so, make sure that
the microinverter is connected to the
network and contact Anker Support.
Check if the DC input of the microinverter
is mistakenly connected to the ground or
contact Anker Support.
A5143
300Wp-730Wp+
28V-45V
16V-60V
60V
20A × 2
25A × 2
799VA
230V/184-253V
3.5A
50Hz/47.5Hz-51.5Hz
0.99
97.30%
99.50%
20mW
-40 °C to 65 °C
-40 °C to 85 °C
263mm × 218mm × 36.5mm
2.8kg
Stäubli MC4 PV-ADBP4-S2&ADSP4-S2
Natural Convection - No Fans
IP67
Wire Size
AC Extension Cable
Cable Length
(Optional)
Plug Type
Communication (Inverter To ECU)
Isolation Design
Features
Energy Management
Compliances
Safety and Grid Compliances
(1) Nominal voltage / frequency range can be extended beyond nominal if required by the utility.
(2) The microinverter may enter Power Degrade mode if there is poor ventilation and heat dissipation in the installation
environment.
Notice
CE RED Declaration of Conformity (For Microinverter)
This product complies with the radio interference requirements of the European Community. Hereby, Anker Innovations Limited
declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is
available at the following website: https://www.anker.com
Bluetooth maximum output power: 18.18 dBm (For EU)
Bluetooth frequency band: 2.4G band (2.402GHz - 2.480GHz)
Wi-Fi maximum output power: 19.86 dBm (For EU)
Wi-Fi frequency band: 2.4G band (2.412GHz - 2.472GHz)
This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to
the applicable collection point for the recycling of electrical and electronic equipment.
Warranty and Customer Service
10-Year Limited Warranty for Anker SOLIX MI80 Microinverter (800W BLE)
Lifetime Technical Support
support@anker.com
(DE) +49 (800) 000 2522
1.5mm²
5M (Default)
Schuko
Built-in Wi-Fi and Bluetooth
High Frequency Transformers, Galvanically Isolated
Energy Management Analysis (EMA) system
EN 62109-1/-2;
EN 50549-1;
DIN V VDE V 0126-1-1; VFR;UTE C15-712-1;
CEI 0-21;
UNE 217002;
VDE-AR-N 4105
EN 10