Aurora WM894XA Manual Del Usuario página 3

OPERATION
Using the switch located on the unit, select one of the following settings by sliding the switch either
left or right. (FIGURE 2)
AUTO / ON :
I
This setting allows the shredder to be automatically started by inserting paper into the
shred opening. Always feed the paper in as straight as possible. When the paper has
passed through, the shredder will automatically stop. (FIGURE 2)
OFF :
O
This setting turns off all features of the shredder. For safety reasons, we recommend that
you leave the shredder in the "Off" position whenever the shredder is unattended or not
in use. (FIGURE 2)
REV ( REVERSE ):
R
In the unlikely event of a paper jam, the reverse setting can be used to help clear the cutters
of paper that has not passed through. Never attempt to clear a jam by using the reverse
function until you have emptied the wastebasket. (FIGURE 2)
Shredding of any of the following materials is considered misuse and will completely
void the product warranty:
Never shred large paper clips, envelopes (any window, insulated, or with glued flaps),
adhesive materials (labels, decals/stickers, glued paper), newsprint, transparencies,
laminated documents, continuous forms, cardboard, or hard and plastic materials
(except Credit Cards).
Only shred credit cards by feeding them vertically into the middle of the entry, releasing when
shredding begins. Never feed more than one credit card at a time. DO NOT ACTIVATE REVERSE
FUNCTION WHILE SHREDDING CREDIT CARDS.
Overfeeding the shredder: Shredding beyond the specified sheet capacity can result in extensive
damage to the shredder. Overfeeding will strain the machine and quickly wear and break the cutting
blades and internal components.
Overheating with extended use: In the event that the shredder has shred continuously beyond
the maximum running time and overheating, the unit will automatically shut off. If this happens, switch
the shredder Off for 30 minutes or longer before resuming normal operation.
4
FIGURE 2
MAINTENANCE
Warning: Failure to properly maintain your shredder will void the warranty. Crosscut
shredders require regular oil lubrication for optimal performance and extended lifespan. We recommend
you oil your shredder once a month. Your basic vegetable or cooking oil (nothing flammable or petroleum
based) can be drizzled onto a few sheets of paper and fed into the shredder.
ONLY USE NON-AEROLSOL VEGETABLE BASED OILS TO OIL YOUR CUTTERS. DO NOT
SPRAY OR KEEP ANY AEROSOL PRODUCTS IN OR AROUND THE SHREDDER. DO NOT USE
CANNED AIR. Be sure to periodically empty the wastebasket to avoid overloading and damaging
the cutting mechanism.
• ALWAYS UNPLUG THE SHREDDER BEFORE CLEANING!
• Only clean the shredder by carefully wiping the unit with a dry soft cloth or towel.
• Do not clean or immerse shredder in water. Having the unit wet may result in damage or
malfunction to the electrical components. If the shredder happens to get wet, be sure to completely
dry the unit immediately with a cloth or towel.
• Never use anything flammable to clean the shredder. This may result in serious injury or damage to
the product.
TROUBLESHOOTING
If there is a problem with your shredder, check below for the symptoms and steps to resolve. If you
continue to have problems, contact customer support at our Service Center. DO NOT ATTEMPT TO
REPAIR BY OPENING THE SHREDDER HEAD. This will completely void the product warranty.
The shredder does not work at all.
a) Make sure the unit is plugged in and that the outlet it is plugged into is in good working order.
b) Overheating with extended use: In the event that the shredder has shred continuously beyond
the maximum running time and overheating, the unit will automatically shut off. If this happens, switch
the shredder Off for 30 minutes or longer before resuming normal operation.
c) Make sure the head unit portion of the shredder is
correctly seated onto the included wastebasket, with all the
words and icons facing towards you. The head unit is
particularly designed to work only with the integrated waste-
basket. Shredders are equipped with a safety interlocking
mechanism, which prevents the shredder from working when
the head unit is lifted, removed, or accidentally knocked over.
On the back center edge of the shredder head, next to the
power cord, is a "curved flap-like shape" that MUST FIT
OVER THE OUTSIDE matching ridge of the wastebasket. The shredder will not function unless the
head unit is properly mounted as pictured.
5
CONTINUED NEXT PAGE