Amoena Custom 300 Instrucciones De Uso página 9

ENG
7. Please note: In order to insert or drain air, the cannula must be inserted completely into the valve.
8. As soon as the correct volume is set, remove the cannula carefully from the valve. The air remains
in the air chamber. Diagram 11 page 04.
9. Now the breast form has been adapted to your individual needs. Remove it from the cup and clean
the valve area with a tissue, as small amounts of care oil from the cannula (tube) may still remain.
Then place the breast form in the pocket of the bra. Sketch 12 on page 04.
Care instructions
• When cleaning, ensure that no water enters the valve.
• Due to the valve, we do not recommend you to wear your Custom when swimming.
• Changes in air pressure can lead to minimal, invisible changes in volume. Adjust the volume with
the pump if necessary.
• Use only the pump supplied with your Custom for any adjustments.
Care instructions for pump
Clean the pump ball, the hose if necessary, and the drain valve with a mild soap solution. Disinfect-
ants that contain alcohol can damage the pump. The proper function of the pump is guaranteed be-
tween -10°C and + 40°C, while the maximum permissible temperature lies between -30°C and +100°C. It
can be disinfected by boiling. In this case, separate the component parts from the pump ball and boil it
in ample water for a short time.
Pump materials
Pump Ball: Soft PVC, phthalate-free
Drain valve: ABS
Hose: Silicone
Cannula: PP
CUSTOM CONTACT BREAST FORMS WITH A SELF-ADHESIVE BACK (304 CUSTOM CONTACT +++)
All Contact products are delivered with a sample size Amoena Soft Cleanser and a soft brush.
Instructions for Use Custom Contact Breast Forms
• The adhesive strength of the breast form can vary depending on your skin type (oily or dry). It is
also dependent on how much you sweat, your level of physical exertion and the condition of the
scar area.
• However, selective adhesion is sufficient to reduce strain on your shoulder and neck.
• The Custom Contact breast form can be worn when playing sport, but adhesion may be reduced due
to the build-up of sweat. The adhesive breast form is chlorine-resistant and salt-resistant. However,
it should be cleaned directly after use in clean water with the Amoena Soft Cleanser.
• Wear the Amoena Custom Contact every day from the beginning. The more regularly the breast
form is worn, the better your skin will accept the adhesive.
16
• In the case of extensive and intensive wear, sweat and small skin particles will build up on the
adhesive surface in the course of the day. This means adhesion will slowly decrease.
• Thorough cleaning of the adhesive surface before putting it back on will give you a renewed feeling
of security.
• If your skin tends towards dryness, apply moisturising skin care after wearing the Contact breast
form.
Putting On the Custom Contact Breast Form
10. First clean your skin carefully. Then let the skin dry fully. The drier and cleaner your skin is, the
better the adhesion of the breast form. Please do not touch the adhesive surface of the breast form,
as this can impair the adhesion.
11. Now put on your bra and check the fit. Next pull your bra strap completely off your shoulder and
arm and lean forwards.
12. Using the hand from your non-operated side, take hold of the bra strap and pull the cup away from
the body.
13. Take the breast form in the other hand and place it in the cup of the bra. The upper corner of the
breast form should be close to the bra strap. Stay leaning forwards. Make sure that the breast form
sits well in the bra. See diagram 1 page 03
14. Cup the outer edge of your bra with your free hand and slowly straighten up. As you do so, carefully
press the breast form onto your body.
15. Now pull the bra strap over your shoulder and press the breast form firmly into place again.
See diagram 2 page 03
16. Check the fit. If the breast form is not well positioned, lean forwards and start over.
Taking Off the Custom Contact Breast Form
1. Cup the breast form with one hand as completely as possible, so that your fingertips are near the
edge, and lean forwards until you feel the weight of the breast form in your hand. Starting at a point
some distance from the scar, slowly pull the breast form off the body.
2. If the adhesive surfaces accidentally stick together as they are removed, they can be easily sepa-
rated again under running water.
3. Please be careful with long fingernails. These can damage the coating of the breast form.
General Care Instructions Custom Contact Breast Forms
• Skin texture and skin evaporations caused by e.g. medications and care products can affect the
adhesive strength. Please clean your breast form daily and thoroughly to achieve optimal and long-
term adhesion.
• Only Amoena Soft Cleanser allows you to achieve optimum adhesion. Other cleaning products can
reduce the adhesive strength.
ENG
17