Installation; Operation; Setup; Cd-Tray - Omnitronic CMP-430 Manual Del Usuario

5. INSTALLATION

(1) Install the CD-player on a plane surface or in your rack.
(2) Make sure that the inclination angle will not exceed 15°, as the CD cannot be read correctly otherwise.
(3) Remove the protection foil from the display.
(4) Please note that the LC-display can only be read from an angle of 45° to the top and of 5° to the bottom.
(5) Rack-installation: This CD-player is built for 19" racks (483 mm). The rack you use should be a Double-
Door-Rack where you can open the front panel and the rear panel. The rack should be provided with a
cooling fan. When mounting the CD-player into the rack, please make sure that there is enough space
around the device so that the heated air can be passed on. Steady overheating will damage your device.
You can fix the CD-player with four screws M6 in the rack. Be aware that fastening the device with four
screws on the front panel is not enough. In order to ensure safety, additional fastening by using ground
and side bars is necessary.
(6) CAUTION: Make sure that the CD-player is switched off (power-switch in outer position) before you
connect it to the mains in order to avoid damages on your loudspeakers.
(7) Connect the CD-player with the RCA-cable to your mixer via the Audio Out-sockets. Make sure that the
right/left occupation (plug-colour red/white) is the same at both devices.
(8) Make sure that the indication on the Voltage-selector corresponds to the available voltage in order to
avoid severe damages. Only plug the power-plug into safety-sockets. Connect your CD-player with the
mains.

6. OPERATION

6.1 Setup

Switch the CD-player on via the Power-switch. If no CD is inserted, „NO DISC" appears on the display.

6.2 CD-tray

(1) Press Open/Close-button in order to open the disc tray. The CD-tray
opens and the display shows "OPEN". Insert your CD in the CD-tray.
Make sure you only hold the CD with two fingers on the edge. Avoid
touching the inside area of the CD.
(2) CAUTION: Do not close the tray by pushing it as this could harm the
construction.
(3) Press the Open/Close-button again in order to close the tray.

6.3 LC-display

the CD is properly positioned, the total number of tracks and the total playback time are shortly displayed.
The player jumps to the first track and is in the Pause-mode (Play/Pause-LED flashes). After reading in a CD
or after selecting a title, the CD player is precisely on the section where the music starts and not at the time
index 0:00:00. This spot is automatically memorized as a starting point.
Above "TRACK" the track number is displayed. Above M (MIN), S (SEC) and F (FRAME) the track remain
time is displayed.
By using the Time-button, the time-indication can be switched from track remain time (Remain) to track
playback time (Elapsed) or total remain time (Total Remain).
Above the time-indication, 10 bars are displayed showing the remaining track-time visually. The shorter the
track remain time becomes, the less bars are displayed. 30 seconds before the track-end, the bars in the
display start flashing.
The indication "SINGLE" means that the CD-player is in Single-mode. The current track is then played once
and the player goes into Pause-mode at the beginning of the next track. By pressing the SGL/CTN-button
again, the CD-player changes back into normal playback mode.
The indication "0.0" means that the playback-speed has not been changed. If you adjust the playback-speed
via the Pitchfader (Pitch-button has to be pressed), the respective percentage is indicated in the display.
After inserting the CD, the total number of tracks and the
total playback time are shortly displayed.
The player jumps to the first track and is in the Pause-
mode (Play/Pause-LED flashes). If the CD is improperly
positioned,"ERR" or "NO DISC" appears on the display. If
21/46 10602415_V_1_0.DOC