Publicidad
IMPORTANT
Please read
these
instructions carefully before you
start
to assemble this
product.
Please
carry
out the
steps
in
the
order
set
out
in
these instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
»
Care
&
Safety Advice
Please
follow
the instructions
as
listed
in
this manual.
Sort the parts
and
check
against
the
contents
list.
For
safety purposes we
strongly recommend the
product
to
be
assembled by
at least
two
people.
Some
parts
have
metal edges.
Please
be
careful
when handling
components.
Always wear
gloves, shoes and
safety goggles
during
assembly.
Do
not
attempt
to assemble the
Gazebo
in
windy
or
wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them away from
children's
reach.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the Gazebo
if
you
are
tired,
have
taken
drugs,
medications
or alcohol,
or if you
are
prone to dizzy
spells.
When
using
a
stepladder or power tools,
make sure
that
you
are
following the
manufacturer's safety advice.
Do
not
climb
or stand on the roof.
Heavy
articles should not
be
leaned against the poles.
Keep
roof
and
gutters
clean
of
snow,
dirt
&
leaves.
Heavy
snow load on roof
can
damage
the
Gazebo,
making it unsafe to stand
below
or
nearby.
This
product
was
designed and
produced for
it's
aimed
purpose
only.
If color
was scratched
during assembly it
can
be
fixed
with the following tints:
Grey
-RAL7012
»
Cleaning Instructions
In
order to
clean
the
Gazebo,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners,
or
other
special
detergents
to
clean
the
panels.
»Tools
&
Equipment
TOO1(Supplied)
»
During Assembly
During assembly
use
a
soft surface below the parts to avoid scratches and
damages.
When
encountering
the information
icon, please
refer
to the
relevant
assembly step for additional comments and
assistance.
Step 6: Carefully
spread silicone
along
the
cross
-section of the
profile
and
immediately attach the profiles
together.
It
is
recommended to wipe
the
extra
residue silicone.
Step
7: It
is
recommended to
use
a
carton or other soft material under the
lowered
corner
in
order to avoid
scratches
and
peeling of paint.
*This note also refers
to
steps 9,10,12
Step
10:
Optional
-
if
you
wish to add curtains
/
mosquito
netting
-
Please
thread the
plastic
clips
through
the
rail in each
profile.
(Curtains
/
mosquito
netting
are
not supplied).
Add clips according
to
the specific
quantity
of curtain
rings.
Steps 12a +14a:
Please
note
that
screws
insertion should
be
done
from
the outside.
Steps
13
+15:
Please
note that
screws
insertion
should
be
done
from
the
bottom
up.
Afterwards
please use
the tool
T001.
Step
16b:
Please
add silicone
on
the inner
area
of
part #7661
as
illustrated.
Step
21a:
Please
drill
holes
in
the panels to
be
located precisely parallel to the holes
in
profiles
#7663.
Step
22:
Please level
the
profiles'
legs and
adapt
screws
and plugs to your specific
ground type.
Please
tighten
all
screws
when completing assembly.
>1
N
Publicidad
