Publicidad
RIO ALU
GB
These instructions are provided for your safety and to facilitate the assembly of the RIO umbrella. Please follow the instruc-
tions carefully. Failure to do so may result in injury or damage. If in doubt contact your dealer.
This symbol indicates very important information. Follow instructions accompanied by this symbol with extreme
care. This does not mean that the other information contained in this handbook is not important.
Keep this handbook for future reference.
IMPORTANT SAFETY INSTRUCTIONS
APPLIES TO ALL IN THIS SECTION
1. INSTRUCTIONS - Please read and follow all the instructions. Damage or injury may result if the umbrella is not
assembled and used as described herein. For safe use it is essential that anyone using the umbrella read all the ins-
tructions in advance. Only persons familiar with the safety aspects should operate this umbrella.
2. PRECAUTIONS - The RIO umbrella serves as a protection from the sun, not as protection from all bad weather. It
must be closed and removed from the frame in the presence of strong winds or thunderstorms, as well as heavy
rain or snow. Always close and remove the umbrella from its frame at night, when you are not at home and whene-
ver it is not under control. The base must be weighed down with a minimum weight of 120 kg (240 Ibs).
COMPONENTS (fig. 1):
C: Base pole
D: Vertical pole
E: Cantilever pole
F: Umbrella
M: Bag of hardware.
BASE ASSEMBLY (fig. 2)
Follow the instructions of the provided base.
Tighten the base bolts well.
Ballast the base with a weight of at least 120 KG (240
Ibs).
FRAME ASSEMBLY (fig. 3 - 3a - 3b - 3c)
1. (fig 3a) Slip the cantilever pole (E) into the vertical pole (D)
and block the two parts with the bolt (P).
Tighten the bolt (P) well.
2. (fig 3b) Insert the vertical pole (D) in the base pole (C).
IMPORTANT: the vertical pole (D) must be pushed all the way
into the square housing of the adjustment ring (0).
3. (fig. 3c) grip the umbrella and slip the umbrella attachment
(R) into the cantilever pole (E)
The umbrella attachment (R) must be pushed all the
way into the cantilever pole (E).
4. When assembling the vertical pole (D) with the attachment
(R) proceed in such way that the position of the pressure
button d' as indicated in (Fig.3a)
5. (fig.3) pass the cord (Z) through the pulley (S).
HOW USE YOUR "RIO"
OPENING THE UMBRELLA (fig.3 - 3d - 9)
IMPORTANT: Before opening the umbrella remove the tie
string and with your hands on the ribs slightly open the
umbrella.
To open the umbrella , gently turn the handle G and fix the
cord in the cleat d' indicated in (Fig.3d).
To give stability to the sunshade fix the cover with the pres-
sure button d' indicated in (Fig.9)
IMPORTANT: to avoid damages release the cover from
the frame before closing the umbrella.
ROTATION OF THE UMBRELLA AROUND THE BASE (fig.
2 - 4)
The frame can rotate 360° around the base and can be fixed
in 20 different positions by inserting the key (U) into the
READ THIS HANDBOOK IMMEDIATELY
ASSEMBLY INSTRUCTIONS
adjustment ring (0) (Fig. 4).
IMPORTANT: The key (U) must be inserted into the adjust-
ment ring (0) at hole (a) of the base pole (C) (fig. 2).
MAINTENANCE AND CARE
REMOVING THE COVER OF THE UMBRELLA (fig. 5 - 6 - 7)
1. (fig. 5) undo screw (V) and free the cord (Z).
2. (fig. 6) release the 6 tabs (X) from the 6 ribs (W).
3. (fig. 7) remove the screw (V') from the umbrella attachment
(R).
4. Remove the umbrella attachment (R) from the umbrella
pole (J).
5. Remove the cord (Z) from the umbrella pole (J) and from
the umbrella attachment (R). In this way you can remove it
(G) from the umbrella.
6. Remove the cover from the umbrella pole (J).
WASHING THE COVER
1. Remove the cover from the umbrella.
2. Wash the cover by hand in lukewarm water 30 °C (90 °F).
3. Allow the cover to dry but do not tumble dry or iron.
4. Replace the cover on the frame.
CHANGING A RIB (fig. 6 - 8 - 8a)
1. Release the 6 tabs from the 6 ribs (W) (fig. 6).
2. Release the rib to be changed (W) from the housing (Y')
pulling forcefully upwards (fig. 8).
3. Rotate the rib (W) 180° and release the other end from the
band (Y") pulling firmly upwards (fig. 8a).
4. Change the rib repeating the above operations in reverse.
STORING THE UMBRELLA AT THE END OF THE SEASON
At the end of the season, before storing your umbrella away,
clean the frame with a damp cloth and dry.
A Check that no parts are damaged. Should any parts
be damaged contact the dealer where it was purcha-
sed and order the spare parts.
Touch up any chipped paint. For perfect conservation of the
RIO during the winter months store in a dry place.
IMPORTANT: to avoid damage caused by mould or oxidation
never put your RIO away when wet or damp.
Publicidad
