JOCCA 5892 Manual De Instrucciones página 10

18-EN
or ice.
-Do not move the appliance when the water tank is full.
-Do not use the appliance with wet hands or with barefoot.
-Never touch the moving parts of the appliance. Never insert your fingers
or other parts of the body in the air inlet or outlet.Never insert any object
that might block up or damage the appliance.
-Do not let the power supply cable touch or come near the hot parts of
the appliance.
-Completely unroll the power cable to avoid overheating.
-Keep the appliance away from any wall (at least, 30 cm).
-Do not shake a device after filling it with water or ice – water can come
out.
-We dissuade the use of adapters, plugs and / or extension cables. If
the above mentioned elements were indispensable, use only simple or
multiple adapters and extension cables that respect the in force procedure
of safety, taking care in not exceeding the limit of power indicated in the
adapter and / or and the extension cable.
-Make sure that the on/off switch is in 0/OFF position before unplugging
it from the mains.
-The appliance must not be used if the grids are not correctly installed.
-The aplliance shouldn't be in touch with curtains, identical papers,
cloths of kitchen, or other inflammable materials during the use.
-Do not use the heater near a bath, a shower or a swimming pool.
-To start using the device you must place the switch On/Off in position I.
The button on the control panel is used only as "Stand by" of the device,
not for disconnection.
WARNING ABOUT THE BATTERIES:
-Remove the battery from its compartment, if you are not going to use
the device for a long period of time.
-Remember that batteries must be deposited in the specialized containers
for battery collection.
-If you want to throw out the device, always remove the batteries before
doing it.
-If the battery has some kind of leak never handle it with bare hands.
-Replace the battery when it is worn out.
-Only the batteries of the same model or equivalent to the recommended
can be used.
-The battery must be placed in accordance with the indicated correct
polarity.
-Never place the battery compartment near fire or heat source.
-Do not throw the batteries into fire or place the control unit to the sun.
-Do not mix new batteries or the old and worn-out.
INSTRUCTIONS FOR USE
Preparation and conditioning of the appliance
-Make sure that the on/off switch is in O position before plugging it from
the mains.
-To fill the water deposit, lift the cap on the top of the device and fill
with water through any of the departments, till the water level indicator
overcomes ("MIN") (fig.2).
IMPORTANT: never overcome maximum water level, ("MAX").Capacity:9L.
-To empty the water deposit, open the cap on the bottom of thedevice
(between the two back wheels). See cleaning section.
WARNING: the deposit could have up to 3 litres of water, even if the
level indicator shows minimum ("MIN").
To start the device
-Connect the device to power supply.
-Now the device is ready to work, to activate the device press the button
I on the control panel and the device will start operating.
-Select the output speed of air you want, the button (5).
- You can select three positions:«I»
- low air flow. «I»
- medium air flow.«II»
- maximum air flow. «III»
-Press the button to select the desired position.
-Button (1). It is used to set the operation time of the device.When the
time is out the device will be automatically disconnected.
-To program it, simply press the button . Each time you press this button
increases the set time a half hour to a total of seven hours. The lights
indicate the scheduled time.
-Wind blow mode (4): To select the Wind blow mode of the device you
have to press the key. With this function the air varies in intensity and
direction gradually. If you want the tabs stay in a certain position, when
they are in the desired position, press the button Wind blow again and
the position will be fixed.
-Cold mode: button (3). To get cooler and humid air place ice in the
largest compartment located at the top of the device (e) or into the
lateral water containers (f) and press. With the light on it also purifies
the air, if the light is off, only cool dry air is coming out.
Make sure that the water level is not under the MIN.
-Heat Mode: place the temperature selector to the heat position and
press the button (2). The hot air will come out.
-Function Mode (6): to select the type of wind blow you have to press the
EN-19