Descargar Imprimir esta página

Urrea UPTC40 Manual De Usuario Y Garantía página 3

Publicidad

CONOZCA SU HERRAMIENTA / KNOW YOUR TOOL
Anillado de color /
Entrada de aire
Color ring
(Aceite
diariamente) /
Air inlet (Oil daily)
Silenciador /
Silencer
SAFETY INSTRUCTIONS
• Always operate, inspect and maintain this tool
in a accordance to hand / held operated pneu-
matic tools.
• Operate this tool at 90 PSI maximum air pres-
sure at the inlet with 3/8" inside diameter air
supply hose.
• Do not lubricate the tool with flammable or
volatile liquids.
• All fittings and hoses should be tightly se-
cured.
• Always shut off the air supply when connect-
ing or disconnecting any tool.
• Always wear safety glasses and hearing pro-
tection when operating the tools.
• You must be in a stable position so that you
can hold the tool firmly.
• Never exceed the recommended air pressure
to increase the performance of the tool.
OPERATION INSTRUCTIONS
For safety use, Please Follow the instructions.
The operation without your local regulations
may cause serious injury. Read thoroughly and
understand this instruction manual and keep
this within reach for future reference.
OPERATION
1. Smooth change of valve reverse (right / left)
button turn direction can be done.
2. Push valve reverse button makes instantly
change direction of air motor rotation.
3. Push-to-Start system eliminates troublesome
to press throttle lever.
4. Adjusting fastening torque by loosening rear
housing and adjusting torque ring:
Tighten to the right: increase torque. Loosen to
the left: decrease torque
5. Air motor will automatically stop when the
load reaches at the pre-set torque.
6. The Torque cove used for:
1) Colour torque system. The colour torque
system gives you an easily visible torque mark-
Válvula de reversa /
Valve reverse
Palanca de
activación /
Lever
ing system at a glance for all the R series tools.
Choice the colour for each torque level used on
your assembly line.
2) Torque fix system. To avoid the adjustment by
operator and easy to mark the torque through
the window. This up-to-the-date design let you
either adjust the torque rapidly or without us-
ing the torque lock nut.
AIR SUPPLY
1. Air tools are adversely affected by moisture.
Since air from compressor contains much mois-
ture and dust, it is desirable to provide a filter
and lubricator in the pipeline to remove such
undesirable elements. Also take the drain out
from air tank every day.
2. When using brand-new air hose or air pipe,
blow and clean the inside of air hose or pipe
before installation.
3. Keep inside of air hose or air pipe clean to
prevent airdrop problem caused by the lots of
drain and dust accumulated and possibly make
the inside diameter smaller in the long use.
4. When disconnect air hose from air tool while
in the operation do not drop air hose end to the
floor as dust or other element may come into
air hose.
5. Use air regulator to keep stable air pressure
at 5,5 kg/cm² - 6,0 kg/cm² at the tool. It is impor-
tant to get proper air pressure at the tool.
6. After lubrication, oil will discharged the ex-
haust upon operation. Flush motor for a few
seconds.
LUBRICATION
1. Lubrication is indispensable to air tools. The
most ideal maintenance is to install one lubri-
cator to a tool for automatic oil feed, but if it
is not available, manual lubrication twice every
day is recommended for longer life and keeping
the efficient function of mechanism.
2. For manual lubrication, disconnect air hose
from bushing air inlet and full up spindle oil
(#40-#60) into the air feed in take and push the
bit.
Anillo indicador de torque /
Torque indication ring
Cubierta del Torque (Sistema
Carcasa trasera /
de torque por color) /
Rear housing
cover (Color torque system)
Retén retráctil de la
punta /
Bit slide sleeve
Torque
3

Publicidad

loading