Publicidad
Idiomas disponibles
Idiomas disponibles
Notes
During Assembly
Use
a
soft platform below the parts to avoid scratches and damages.
Please
note you install the panels
with
the
UV
protected
side
out (marked with
"THIS
SIDE
OUT")
remove plastic sticker
as
panels
are
locked
in place.
Product dimensions
can be
adjusted to your specific
needs:
1. The
wall-mounting profile (top-back)
can be
adjusted from 260
to
305 cm
(102.4" to 120")
above ground.
The
adjusting
is
done when measuring and drilling (Step
5).
Please
note the installation recommendations' height suggested
in
Diagram
A.
It
is
possible to fix the Patio Cover back wall
height
at
the lowest point of 260 cm/102.4".
This
method
is
optional if the assembly
conditions
and
exterior
walls do
not allow to follow the suggested installation
as
appears
in
the manual.
Please
note
that
the product appearance may slightly change
as
a
result,
however snow load weight does not change.
2.
Poles
distance from the wall
can be
adjusted from 226
to 286
cm
(89" to 112.5")
as
suggested
in
Diagram
Bl.
Poles
distance from the
side edges can
be
adjusted from
5
to
54 cm
(2" to 21.3")
as
suggested
in
Diagram
B2.
The
adjusting
is
done after assembly and before anchoring (Step 16)
by
sliding
poles and
profile 7708+7707
at
the roof profiles'
channels.
3. Wall
mounting
and distance from the wall determine the roof angle and the total depth
of
the product (distance
of gutter
from
the wall). Higher wall mounting and shorter distance between wall and
poles increase
the roof angle and shorten the total depth
a
s
suggested
in
Diagram
C.
Steps
Step
5:
It
is
important
to plan the installation
area,
mark
as
per the instructions and level the surface
prior to the
assembly.
Make
sure
you
use
suitable
screws
and anchors.
Step 7: Apply silicone sealants above beam 7288,
in
order to prevent water from seeping
in.
Step
9:
Make
sure
that the angle between the back wall profile and the
panel
supporting
profiles
is
90
degrees.
Step 11:
Please
note you install the panels
with
the
UV
protected
side
out (marked with
"THIS
SIDE
OUT")
remove plastic sticker
as
panels
are
locked
in place.
Step 14a: Apply silicone sealants
on
the inner part
of
7997, and connect to the profile
as
depicted
in
drawing
14a.
Step 14c:
Do
not
tighten
screw
4043
yet,
in
order to allow the final adjustments done
in
step 16b.
Step 16a+1
6c: Please
adjust the
poles (inside
out
and sideways) by sliding them to
their
final position prior to anchoring. Make
sure
that the
poles
distance from the
Patio
cover side edge does not exceed 54 cm/21.3".
Step 16b: Adjust the
gutter
head's
angle according to your needs and
tighten
screws
4043.
Step 18: Anchoring this product to the ground
is
essential to its
stability
and rigidity.
It
is
required to complete this stage
in
order for your warranty to
be
valid.
*Tighten
all screws
when completing assembly.
Note:
The
wall anchoring kit supplied
with
this product
is
suitable for concrete or solid brick walls
only.
Other wall types need
an
accordant wall fixation kit.
II
260-305cm
102.4"-120"
226-286cm
89"-
112.5"
.
.
17°
.
13°
+
*;
+
Publicidad
