Publicidad
Idiomas disponibles
Idiomas disponibles
Refer to Figures 4 and 5.
Check for shipping damage. If damage has occurred, a claim
must be filled with carrier. Check for completeness.
Immediately report missing parts to dealer.
The sander comes assembled as one unit. Additional parts
which need to be fastened to sander, should be located and
accounted for before assembling.
• Auxiliary Table (Fig. No. 4, Key No. 56)
• Auxiliary Table Post (Fig. No. 4, Key No. 54)
• Locking Handle (Fig. No. 4, Key No. 52)
• 5/_"-3/8 Set Screw (Fig. No. 4, Key No. 55)
° Foot Rest (Fig. No. 5, Key No. 34), 4 each
° 5/_-18 x 1" Hex Head Bolt (Fig. No. 5, Key No. 1), 4 each
° 5/_,,Flat Washer (Fig. No. 5, Key No. 2), 8 each
° 5/_-18" Hex Nut (Fig. No. 5, Key No. 28), 4 each
° Replace shelf in cabinet.
° Close cabinet door and secure it with knob.
ATTACH
AUXILIARY
TABLE
Refer to Figure 4.
Required parts and hardware:
° Auxiliary table
° Auxiliary table post
° Locking handle
° 5/_-18 x 3/8"Set screw
NOTE: It is not necessary to have the auxiliary table mounted
at all times. Table can be installed only when needed.
D
* Insert auxiliary table post in auxiliary table (Key Nos. 54
and 56).
° Secure in position with set screw (Key No. 55).
° Slide post into bracket (Key No. 53).
° Secure in position with locking handle (Key No. 52).
Refer to Figures 1, 2, and 3, pages 4 and 5.
CAUTION:
Do not attempt assembly if parts are missing.
Use this manual to order replacement parts.
Before sander is assembled, a suitable location should be
chosen. The sander with cabinet weighs approximately 200
Ibs when completely assembled. They should be assembled
on location.
• Sander needs to be set on a flat, level surface.
• Make sure there is ample room for moving the workpiece
through the entire cut. There must be enough room that
neither the operator nor the bystanders will have to stand in
line while using the tool.
• Good lighting and correct power supply are also required
for a proper work area.
ATTACH
FOOT
RESTS
Refer to Figure 5.
Required parts and hardware:
• Four foot rests
• Four %o-18 x 1" Hex head bolts
• Eight 5/_o" f lat washers
• Four 5/lO"-18Hex nuts
CAUTION:
Sander with cabinet weighs approximately
200 Ibs. At least two people are required to attach foot rests.
• Loosen knob (Key No. 32) and open cabinet door (Key No.
31).
• Remove shelf (Key No. 33) from cabinet (Key No. 29).
• Carefully tip the sander to raise cabinet from the floor just
enough so that one foot rest with bolt and washer (Key Nos.
1, 2 and 34) can be positioned under the cabinet corner so
that the bolt slides through the hole on the cabinet base.
Slowly set the sander back to the floor. Repeat three more
times to position one foot rest with bolt, under each cabinet
corner.
• Using the cabinet door opening, secure foot rests to cabinet
using four flat washers and four hex nuts (Key Nos. 2 and
28).
° Make sure all the hex nuts are tight.
Sander comes with the motor and wiring installed. The
110/220-volt AC induction motor has the following specifica-
tions.
Horsepower (Continuous duty) ......................
3/4
Amperes ...................................
10.0/5.0
Frequency
...................................
60 HZ
Phase .......................................
Single
RPM .........................................
1720
Prewired
.....................................
110V
WARNING:
All electrical connections must be performed by
a qualified electrician.
WARNING:
Do not connect sander to the power source until
all assembly steps have been completed.
POWER
SOURCE
The motor is designed for operation on the voltage and fre-
quency specified. Normal loads will be handled safely on volt-
ages not more than 10% above or below specified voltage.
Running the unit on voltages which are not within the range
may cause overheating and motor burn-out. Heavy loads
require that the voltage at motor terminals be no less than the
voltage specified on nameplate.
°
Power supply to the motor is controlled by a single pole
locking rocker switch. Remove the key to prevent unautho-
rized use.
GROUNDING
INSTRUCTIONS
WARNING:
Improper connection of equipment grounding
conductor can result in the risk of electrical shock. Equipment
should be grounded while in use to protect operator from
electrical shock.
* Check with a qualified electrician if grounding instructions
are not understood or if in doubt as to whether the tool is
properly grounded.
* This tool is equipped with an approved 3-conductor cord
rated at 240V and a 3-prong grounding type plug rated at
125V (Figure 1) for your protection against shock hazards.
Publicidad
