Craftsman 351.226060 Manual Del Operador página 6

The two dust collection chutes accept the standard 4" dust
collection hose for quick removal of dust. The adjustable miter
gauge can be used on both the belt and disc tables for guid-
ing the workpiece at a desired angle while sanding.
SPECIFICATIONS
Belt size ............................ 6 x 48", 100 grit
Belt platen area .......................... 6% x 167/8 "
Belt table dimensions ....................... 5'/8 x 9'/8"
Belt table tilts .............................. 0 to 45 °
Belt dust chute diameter .......................... 4"
Belt speed .............................. 1570 FPM
Disc diameter .......................... 12", 100 grit
Disc table dimensions ........................ 7 x 16"
Disc table tilts ....................... 0 to 45 ° outward
.................................. 0 to 20 ° inward
Disc dust chute diameter .......................... 4"
Disc speed .............................. 2000 RPM
Base dimensions .................... 23Vz x 21 x 55'/2"
Switch ................... 120 Volts, SP, Locking rocker
Motor ................ 3HP (max. developed) 3450 RPM
.................................. 115V, 15 AMPS
Weight .................................... 195 Ibs
WARNING:
Operation of any power tool can result in foreign
objects being thrown into eyes which can result in severe eye
damage. Always wear safety goggles complying with United
States ANSI Z87.1 (shown on package) before commencing
power tool operation. Safety goggles are available at Sears
retail stores or catalog.
CAUTION:
Always observe the following safety precautions.
SAFETY PRECAUTIONS
• Whenever adjusting or replacing any parts on the tool, turn
switch OFF and remove the plug from power source.
• Recheck table handles. They must be tightened securely.
• Make sure all guards are properly attached.All guards
should be securely fastened.
• Make sure all moving parts are free and clear of any
interference.
• Make sure all fasteners are tight and have not vibrated
loose.
• With power disconnected, test operation by hand to verify
clearance and adjust if necessary.
• Always wear eye protection or face shield.
• Make sure abrasive belt tracks properly. Correct tracking
gives optimum performance.
• After turning switch on, always allow belt to come up to full
speed before sanding or grinding.
• Be sure motor runs clockwise on disc side. Abrasive belt
must travel down.
• Keep your hands clear of abrasive belt, disc and all moving
parts.
• For optimum performance, do not stall motor or reduce
speed. Do not force the work into the abrasive.
• Support workpiece with belt table when sanding with belt,
with disc table when sanding with disc.
• Never push a sharp corner of the workpiece rapidly against
belt or disc. Abrasive backing may tear.
• Replace abrasives when they become loaded (glazed)or
frayed.
• When grinding metal, move workpiece acrossabrasive to
prevent heat built up.
• Never attempt wet sanding.If the workpiece becomes too
hot to handle, cool it in water.
POSITION BELT TABLE
Refer to Figures 8 and 11.
The belt table (Key No. 53) can be tilted from 0° (at right
angle to the table) to 45 ° .To adjust belt table position:
• Unlock the handle (Key No. 18) on the right side of table.
__ _.Table Lock Handle
Rgure 8 - Attach Belt Table
• Set the belt table to any angle between 0° and 45 ° using
the scale.
• Lock the handle to secure belt table position.
WORK STOP
Refer to Figure 11.
The work stop (Key No. 31) can be used instead of the belt
table.
• Remove belt table from the belt housing (Key No. 48) by
loosening and removing handle (Key No. 16).
• Mount workstop using bolt (Key No. 15) and washer (Key
No. 13) which are located on belt housing.
ADJUSTING BELT HOUSING
Refer to Figures 9, 11 and 12.
The belt housing (Figure 11, Key No. 48) can be positioned at
a full vertical position, a full horizontal position, or at any
angle in between which is convenient for the sanding opera-
tion.
To adjust belt housing position:
• Loosen and remove three knobs (Figure 12, Key Nos. 7
and 27).
• Remove dust hood (Figure 12, Key No. 28).
• Loosen he)( nut (Figure 11, Key No. 38).
• Move to the rear of the sander.
• Loosen hex nut (Figure 11, Key No. 38) below the belt
cover (Figure 11, Key No. 49).
• Gently push belt housing to move to the desired angle
using the soale.
• A positive stop bolt (Figure t2, Key No. 30) is provided to
stop the belt housing at the full horizontal position.
• Tighten both hex nuts (Figure 11, Key No. 38) to secure
belt housing position.
• Replace dust hood using the knobs.
6