Notes On The Plug; Electric Power; Parts; Before Using For The First Time - CHEF-BUILT CCB-1000 Manual De Instrucciones

NOTES ON THE PLUG

This appliance has a grounded 3-prong plug. Connect to a properly
grounded outlet only. If the plug does not fit fully into the outlet, contact
a qualified electrician. Do not attempt to modify the plug in any way.
G
CCB-1000 – 120V 3.2Amp; NEMA 5-15P Plug; ETLus APPROVED
W

ELECTRIC POWER

If the electrical circuit is overloaded with other appliances, your
appliance may not operate properly. It should be operated on a
separate electrical circuit from other appliances.

PARTS

Figure 1
44oz. Power Blender
1. Removable Lid Cap
(doubles as 2oz. measuring cup)
2. Jar Lid
3. 44 oz. Tritan Jar
4. Stainless-Steel Blades
5. Motor Base
6. Control Panel
7. 120V 3-Prong Plug (not shown)
8. ON/OFF (I/O) power switch
9. Non-Skid Feet
Control Panel
10. Timer
11. STOP Button
12. LOW and HIGH Buttons
13. PULSE Button
SO-315117_18061 Chef-Built_HP Blender CCB-1000_Sensio_IM_R7.indd 4-5
1
2
3
4
5
7
6
8
9
10
13
11
12
4

BEFORE USING FOR THE FIRST TIME

1. Carefully unpack the Power Blender and remove all packaging materials
2. Following the detailed procedures described in CARE & CLEANING
INSTRUCTIONS, wash, rinse, sanitize and dry blender parts before assembly.
3. Clean and sanitize the motor base.
WARNING: NEVER IMMERSE THE MOTOR BASE OR CORD IN WATER.

SOFT START

1. This Chef-Built Power Blender features a 3 second "soft start."
2. Blending will gradually increase until desired speed setting is reached.
44 . TRITAN JAR ASSEMBLY INSTRUCTIONS
®
oz
1. Handle stainless steel blades by the blade collar only.
2. WARNING! BLADES ARE SHARP! Handle carefully. Use extreme care when
handling. Failure to do so can result in personal injury.
3. Position rubber seal over blade assembly so that it sits in
between the flats of the blade assembly and the jar.
4. Inset blade assembly with rubber seal into the bottom hole
of the jar.
5. Turn the jar upside down, on a clean, sturdy surface.
6. Using the blade's collar to handle, position the blade collar/
stainless steel blades upside down into the bottom jar
opening as shown.
7. Twist the blade collar clockwise until snuggly attached onto
the jar.
8. CAUTION: Always check to be sure the blade collar is properly fitted into the
jar before use.

OPERATING INSTRUCTIONS

1. Place the motor base on a flat, clean, dry counter top or table, away from
flammable materials.
2. Make sure the unit is unplugged. Check to make sure the ON/OFF (I/O) switch on
the side of the motor base is in the OFF (O) position.
3. Place the jar on the motor base so that the jar coupler and motor coupler are
aligned and engaged.
IMPORTANT: Make sure the jar is properly fitted onto the motor base before
adding food for blending.
4. Add food to be processed to the jar.
WARNING: When blending, foods or liquids tend to expand and rise up the side
of the jar. To avoid personal injury, leakage or damage to the Bar Blender.
DO NOT FILL JAR WITH FOOD PAST THE MAX FILL LINE.
5. Place the lid on top of the jar and press firmly to seal. To avoid spills, make sure
the lid is secure and the lid cap is in place before operation.
6. Plug the power cord into a 120V AC 3-prong electrical outlet.
7. Press the ON/OFF (I/O) switch to ON (I). The white LEDs for timer and all 4 key
indicators light up for a second.
5
2018-08-31 10:38 AM