Craftsman 917.376580 Manual Del Usuario página 15

chillaenet
_equelaranura
,_terodel cigue-
tador de _sta
3s en la cuchiHa
n el adaptador,
:le salida de
afilado) est_
a con la aran-
lela endurecida
a y el ciguehal.
ltre la cuchilla
)riete el perno
I sentido en que
iendada es de
Chavelero del
ciguenal
Cigudnal
uchilla es
;ustituir los
nos aprobados
de ReparaciGn
:itarla cuchilla
que quede
cuidado de
chiila que no
ventualmente
[or.
una lima o en
ate de afilada
_egadora,
3uchilla, clave
)are& Deje
un clavo recto
.=ntralde la
lavo. Si la
e permanecer
ualquiera de
mueve hacia
hasta que #sta
e ser rociado
)ero tiene que
usar,
ed a menudo
deteriorado.
normal, Si se
r, c#.mbielo
,&CAUTION: Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with plug.
• Clean the underside of your lawn mower
by scraping to remove build-up of grass
and trash.
• Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
• Keep finished surfaces and wheels free
of all gasoline, oil, etc.
,&WARNING: To avoid serious injury,
before performing any service and
adjustments:
1. Release control bar and stop engine,
2. Make sure the blade and all moving
parts have completely stopped.
3, Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with plug_
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See "TO ADJUST CUTTING HEIGHT" in
the Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the
rear wheels of your mower, is provided to
minimize the possibility that objects will
be thrown out of the rear of the mower
into the operator mowing position,, if the
deflector becomes damaged, it should be
replaced,
TO REMOVE DRIVE BELT
1. Remove drive cover and belt keeper°
2_ Remove belt from gearcase pulley by
pushing down on pulley and rolling belt
off it,
3. Turn lawn mower on its side with air
filter and carburetor down.
4, Remove blade and debris shield.
5_ Remove belt from engine pulley on
crankshaft.
TO REPLACE DRIVE BELT
1_ Install new belt on engine pulley_
2. Reinstall debris shield and blade.
3. Return mower to upright position.
4. Install new belt on gearcase pulley.
5. Reinstall belt keeper and drive cover.
NOTE: Always use factory approved belt
to assure fit and long life.
• We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in short-
ened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a sea-
son. Scrape underside of cover with putty
knife or similar tool to remove any build-up
of trash or grass on underside of drive cover.
Drive
cover
Belt ",
keeper
PUSH
DOWN
TO ADJUST HANDLE
The handle can be mounted in a high or
low position, The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
1, Remove upper handte and wire tie(s)
securing cable(s) to lower handle.
2, Remove hairpin cotters from lower
handle bracket mounting pim
3_ Squeeze lower handle in to remove it
from mounting pins,
4, Turn lower handle over to raise or
lower handle,
5, Squeezelowerhandleinandposition holes
onto mounting pins on handle brackeL
6. Reassemble upper handle and all
parts removed from lower handle°
Mowing Mowing
,_/po sition ["i z>. position /';_
Ha
_F Handle _ X (_
rfl
15 pin LOW POSITION HIGH POSITION