English
11. Press the Enter / Information button to complete setup.
will be displayed on the LCD.
○ To cancel the alarm setting, go to "BUZZER ALM" once
again and change the setting to "
○ The alarm sound will automatically switch off after 10
minutes. The sound can also be switched off by pressing
any button.
NOTE
The volume of the buzzer alarm cannot be changed.
● Setting the radio ON alarm timer
Using the radio ON alarm timer function, the radio can be
set up to switch ON at a specifi c time to enjoy a station
broadcast.
1. Press the Menu button.
2. Press the Select button and display "RADIO ALM".
RADIO ALM
3. Press the Enter / Information button.
4. Press the Select button and display "
ON
5. Press the Enter / Information button.
6. Press the Select button and adjust "hour" digits.
12 : 00
7. Press the Enter / Information button.
8. Press the Select button and adjust "minute" digits.
12 : 55
9. Press the Enter / Information button.
10. Press the Select button to set up repeat.
Once
Daily
Weekdays only
Saturday and Sunday only
DAILY
11. Press the Enter / Information button.
12. Select radio bandwidth.
Press the Select button to display "AM" or "FM".
FM
13. Press the Enter / Information button.
14. Press the Select button to display a preset station.
P2 FM 79.5 MHz
To select a station by broadcast frequency, use the
Search button.
FM 80.0 MHz
15. Press the Enter / Information button to complete setup.
○ To cancel the radio alarm setting, go to "RADIO ALM"
".
NOTE
RECHARGING YOUR SMARTPHONE
Devices such as a smartphone and mobile phone can be
recharged by connecting the device to this radio.
The recharge function is only available for the "
mode. (Recharging cannot be done in "
NOTE
○ When recharging in "
○ On rare occasions, sound output may be interrupted or
".
○ The radio is designed to deactivate USB output and
○ If the voltage is low when the AC adapter is in use, the
1. Using a commercially available USB connection/
2. Secure the smartphone with the holders and close the
NOTE
○ Use a fully charged battery when using a battery as this
ONCE
DAILY
○ The time required for charging varies in accordance with
WEEKDAY
○ Do not use the recharge function for any devices other
WEEKEND
○ The radio may not be able to recharge some smartphone
Two recharge cable holders, one for Android and the other
for Apple (Lightning connector) are included.
Select the holder that best suits your device.
○ Should your device be too large for the radio's external
NOTE
MAINTENANCE AND INSPECTION
WARNING
10
will be displayed on the LCD.
once again and change the setting to "
The radio's volume will be at the level when the radio
was last switched OFF.
at 20 or less.
The radio is designed to deactivate USB output and
disable the recharging of smartphones and mobile
phones when the volume is at 21 or more.
(For "
" mode, USB recharging will continue even if
the volume output is 21 or more.)
power could shutdown during USB recharging.
If either should occur, lower the volume level or stop
recharging with the USB.
disable the recharging of smartphones and mobile
phones when the power level of the battery is low.
Should the aforementioned occur, recharge the battery
or replace with a fully charged battery.
USB output may be cut off , discontinuing any recharging.
recharge cable, connect to the USB charging port
located in the radio's storage case for external devices.
(Fig. 9)
cover. (Fig. 8)
(See "Secure the external device" on page 9)
device's power source.
You will not be able to recharge smartphones or mobile
phones when the battery power level becomes low.
the smartphone or mobile phone being recharged.
than a smartphone or mobile phone.
or mobile phone models.
device storage case, draw the cable through the cable
access hole. (Fig. 10)
As the recharge cable holders are designed for standard
size terminals, the holders may not be able to securely
fasten certain terminals depending on the recharge
cable used.
When not in use or during inspection and maintenance,
be sure to remove the AC plug, rechargeable battery and
backup batteries.
".
" or "
" mode.)
" mode, set the volume output
"