Braun BC13 Instrucciones Para El Usuario página 2

English
Battery precautions
1. Do not use rechargeable batteries.
2. Use only alkaline AA/AAA batteries of the same or equivalent
type.
3. Insert batteries with the correct polarity.
4. Keep batteries away from children.
5. Dispose of exhausted batteries according to local legal re-
quirements. Do not dispose them by throwing away with normal
household rubbish.
6. Avoid short circuiting the contacts in the battery compartment
and battery terminals.
7. Remove batteries from the unit if it will not be used for long
period of time.
8. Exhausted batteries should be removed from the battery com-
partment to prevent over-discharge, which can cause leakage
and may cause damage to the clock.
Getting started
1. Remove the battery door.
2. Insert 2xAA size new batteries in the main unit and 2xAAA size
new batteries in the sensor as indicated in the battery compart-
ments.
3. To pair the main unit with the sensor, press the RESET key at the
back of the main unit first, and then press the RESET key inside
the battery compartment of the sensor.
4. In some cases the main unit and the sensor will not pair imme-
diately. You can reset the main unit and the sensor again as de-
scribed in the above section. Due to the atmospheric disturbance,
the best reception often occurs during night time.
5. Close the battery door.
Function keys – main unit
TIME SETTING / NEUTRAL / ALARM SETTING switch
- Slide the switch to the TIME SETTING position to set the clock
time.
- Slide the switch to the ALARM SETTING position to set the
alarm time.
- Slide the switch to the NEUTRAL position to exit the setting
mode and return to normal display.
+ Key
- When the setting switch is in the NEUTRAL position, press the
+ key to change between 12 and 24 hour display format.
- In TIME SETTING or ALARM SETTING mode press to increase
the setting value. Press and hold to speed up the setting.
- Key
- When the setting switch is in the NEUTRAL position, press
the - key to change the temperature display between °C and
°F format.
- In TIME SETTING or ALARM SETTING mode press to decrease
the setting value. Press and hold to speed up the setting.
ALARM ON / OFF slider
- Shift the ALARM ON / OFF slider up to enable the alarm, the
alarm time will show on the LCD display for 3 seconds.
- Shift the ALARM ON / OFF slider down to disable the alarm.
SNOOZE / LIGHT touch button
- Tap to turn on the backlight for 10 seconds.
- Tap to stop the alarm and activate the 5 minute snooze func-
tion.
RESET key
- Press by using a pin to reset all values to default. In case of a
malfunction, the unit has to be reset.
PAIR button
- Press to receive 433 MHz signal for sensor reception.
BACKLIGHT ON /OFF switch
- Slide the switch to ON position to enable the night light mode.
- Slide the switch to OFF position to disable the night light
mode.
Function keys – sensor
°C / °F key
- Press to switch between °C / °F display.
RESET key
- Press by using a pin to reset all values to default. In case of a
malfunction, the unit has to be reset.
Product description – main unit (Image 1)
1. LCD display
2. SNOOZE / LIGHT touch button
3. ALARM ON / OFF slider
4. TIME SETTING / NEUTRAL / ALARM SETTING switch
5. + Key
6. - Key
7. Battery compartment
8. RESET key
9. PAIR button
10. BACKLIGHT ON / OFF switch
Display details – main unit (Image 2)
A. Time
B. AM / PM indicator (for 12 hour format)
C. Alarm icon
D. Indoor temperature
E. Outdoor temperature
F. Indoor humidity
G. Outdoor humidity
H. Low battery indicator
I. Weather forecast indicator
J. Sensor signal indicator
Product description – sensor (Image 3)
1. LCD display
2. Wall mounting holder
3. Battery compartment
4. °C / °F switch
5. RESET key
Display details – sensor (Image 4)
A. Outdoor temperature
B. Outdoor humidity
C. Low battery indicator
D. Sensor signal indicator
Setting the time
1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the TIME SETTING position.
2. Press the '+' or '-' key to set the desired value. Press and hold the
'+' or '-' key to speed up the setting.
3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the NEUTRAL position to return the normal display and save the
settings.
Setting the alarm
1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the ALARM SETTING position.
2. Press the '+' or '-' key to set the desired value. Press and hold the
'+' or '-' key to speed up the setting.
3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the NEUTRAL position to return the normal display and save the
settings.
Using the alarm and snooze function
1. Enable the alarm by shifting the ALARM ON / OFF slider up (so
the green detail is visible). The bell icon will appear on the LCD
display, and the alarm time will show on the LCD display for 3
seconds.
2. Tap the SNOOZE / LIGHT touch button to stop the alarm and ac-
tivate the snooze function. When the snooze function is activated,
the bell icon will flash.
3. To disable the alarm and snooze function, shift the ALARM ON /
OFF slider down. The bell icon will disappear.
Note: When the snooze function is activated, the alarm will auto-
matically start again after 5 minutes. The snooze function will not
stop unless the ALARM ON / OFF SLIDER is shifted down.