DOMPEL FREEDOM Manual De Instruccion página 4

Install your Dompel product in a level place with no grooves or splices,
preventing rocking and vibration. The location must be airy and it must not allow
straight sunlight and it must be away from sources of heat (stoves, ovens, etc.)
and flammable products. Do not install your product outdoors.
Do not use metal spatulas, brushes and cleaning agents such as alcohol, acetone, kerosene, gasoline, bleach,
thinner, solvents, varsol, vinegar or other chemicals or abrasives such as sandpaper or steel brushes.
To easily clean it, use a solution of warm water with a neutral soap and then wipe dry carefully. If chemical products
reach the upholstery, clean as soon as possible, preventing the products from staining or drying the fabric. The
plastic parts can not be washed with boiling water. Chromed metal components can be cleaned with a soft, dry
flannel, and silicone-based automotive wax can be used to increase gloss and durability, in this case perform the
task following the wax manufacturer's instructions. Perform periodic cleaning, accumulated dust affects the beauty
of the product making it difficult to clean the product.
Two
Entrances
Faucet
Matal
Clamp
Hose
Connector
Hose
Seal
Washer
Two entrances faucet assembly: Assemble the faucet (G)
and shower (G) in the basin (A), remove the metal clamp
and the hose connector from the single lever faucet and fit
the upper part of the basin. Then, assemble the metal clamp
and thread the hose connector securing the single lever.
When assembling the hose, make sure that the smaller
sealing washer is correctly fitted to the hose connection.
Thread the shower on the connector.
Fit the headrest (D) manually into the basin (A).
Place (with some
protection to avoid
scratching) the basin
assembly (A) on the
floor and position the
base of the basin (C)
for assembly. Use a
support base (it can be
a chair) to make the
task easier.
Fit the base (C) to the
seat (B). Place the
structure set with the
basin (A) on the floor
(with some protection to
avoid scratching) and
position it on the seat
(B). To make the task
easier, place the seat on
a support (it can be a
chair).
Turn the wash unit over and
assemble the basin
accessories according to
the version and type of
installation required.
Connect the faucet set,
hoses and shower (G) to
the basin (A) according to
items 6, 7 and 8.
Shower
Shower
connector
Avoid accidents. After
unpacking the product, keep
all the pack material out of
children's reach.
Faucet
Head
Finishing
Faucet
Plastic faucet one entrance assembly : Mount the faucet
set (G) and shower (G) in the basin (A): remove the
attached handle and the finishing of the threaded faucet.
After, fit the faucet on the bottom of the basin and screw
the finishing on the faucet on the top of the basin giving
the necessary tightening. Refit the handle manually.
Thread the shower on the connector.
Installation without heater
Water faucet
hose to the
shower
Water faucet
hose to the
water inlet
Install the
hoses (G)
connecting to
the faucet (G) in
the options as
shown in the
images and
according to the
need.
Fasten the base (C) to
the basin assembly (A)
by screwing the screws
(E) 4 x 16 mm using a
Phillips screwdriver.
Connect the base
structure (C) to the
seat (B), fixing the
screws (F) 5 x 16
mm. Use a Philips
screwdriver.
Shower
Shower
Connector
Installation with heater
Heater
Heater
holder
support
screws
Water faucet
hose to the
heater (DOES
NOT INCLUDE)
Water faucet
hose to the
heater (DOES
NOT INCLUDE)
Clamp for
heater
Shower
attachment
hose to
heater
Faucet installation two entrances
Water
Hot water
faucet
faucet hose
hose to
for shower
the
shower
Cold water
faucet
hose for
shower