Publicidad
Idiomas disponibles
Idiomas disponibles
........
?
OPERATE
YOUR
SAW SAFELY
• Do not operate with one hand. Seri-
ous injury to the operator, helpers, or
bystanders may result from one-
handed operation. A chain saw is in-
tended for two-handed use.
• Operate the chain saw only in a well-
ventilated outdoor area.
• Do not operate saw from a ladder or
in a tree, unless you are specifically
trained to do so.
• Make sure the chain will not make
contact with any object while starting
the engine. Never try to start the saw
when the guide bar is in a cut.
• Do not put pressure on the saw, es-
pecially at the end of the cut. Doing
so can cause you to lose control
when the cut is completed.
° Stop engine before setting saw down.
• Hand carry saw only when engine is
stopped. Carry with muffler away from
body; guide bar & chain projecting be-
hind you; guide bar preferably cov-
ered with a scabbard.
MAINTAIN
YOUR
SAW
IN GOOD
WORKING
ORDER
- Have all chain saw service performed
by a qualified service dealer except
the items listed in the maintenance
section of this manual.
• Make certain the saw chain stops
moving when the throttle trigger is re-
leased. For correction, refer to "Car-
buretor Adjustments."
• Keep the handles dry, clean, and free
from oil or fuel mixture.
• Keep caps and fasteners securely
tightened.
• Use only Craftsman accessories and
replacement parts as recommended.
Never modify your saw.
HANDLE
FUEL WITH
CAUTION
• Do not smoke while handling fuel or
while operating the saw.
• Eliminateall sources of sparks or flame
in areas where fuel is mixed or poured.
• Mix and pour fuel in an outdoor area
and use an approved, marked con-
tainer for aU fuel purposes. Wipe UP
all fuel spills before starting saw.
• Move at least 10 feet (3 meters) from
fueling site before starting.
Turn the engine off and let saw cool in
a non-combustible
area, not on dry
leaves, straw, paper, etc. Slowly re-
move fuel cap and refuel unit.
• Store the unit and fuel in a cool, dry
well ventilated space where fuel va-
pors cannot reach sparks or open
flames from water heaters, electdc
motors or switches, furnaces, etc.
GUARD
AGAINST
KICKBACK
Follow all safety rules to help avoid
kickback and other forces which can
result in serious injury.
_
.,,._/,
Kickback Path
Avon Obstructions
Clear The WorkingArea
WARNING;
Rotational Kickback can
occur when the moving chain contacts
an object at the upper portion of the tip
of the guide bar, Contact at the upper
portion of the tip of the guide bar can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back
toward the operator.
Pinch-Kickback and Pull-In occur when
the chain is suddenly stopped by being
pinched, caught, or by contacting a for-
eign object in the wood. This sudden
stopping of the chain results in a rever-
sal of the chain force used to cut wood
and causes the saw to move in the op-
posite direction of the chain rotation.
Pinch-Kickback drives the saw straight
back toward the operator. Pull-In pulls
the saw away from the operator.
REDUCE
THE CHANCE
OF
KICKBACK
• Recognize that kickback can happen.
With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
• Never let the moving chain contact
any object at the tip of the guide bar.
• Keep working area free from obstruc-
tions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate
or avoid any obstruction that your saw
chain could hit while cutting.
• Keep saw chain sharp and propedy
tensioned. A loose or dull chain can
Publicidad
