Publicidad
Idiomas disponibles
Idiomas disponibles
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the device owner
to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not legible, contact SUNEX for
replacements. If the operator is not fluent in English, the product and safety instructions shall be read and discussed with the operator in the operator's
native language by the purchaser/owner or the designer, making sure that the operator comprehends its contents.
THIS
INSTRUCTION
CONTAINS IMPORTANT SAFETY
INFORMATION.
READ
THIS
INSTRUCTION
CAREFULLY
AND
UNDERSTAND
INFORMATION BEFORE OPERATING THIS
TOOL.
• Read and understand all instructions. Failure
to follow all instructions listed below, may
result in electric shock, fire, explosion and/or
serious personal injury. It is the responsibility
of the owner to make sure all personnel read
this manual prior to using the device. It is also
the responsibility of the device owner to keep
this manual intact and in a convenient location
for all to see and read. If the manual or product
labels are lost or not legible, contact SUNEX
for replacements. If the operator is not fluent
in English, the product and safety instructions
shall be read and discussed with the operator
in the operator's native language by the
purchaser/owner or his designee, making sure
that the operator comprehends its contents.
• Always operate, inspect and maintain
this tool in accordance with American
National Standards Institute Safety Code of
Portable Air Tools (ANSI B186.1) and any
other
applicable
safety
regulations.
• For safety, top performance
and maximum
parts, operate this tool at 90 psig;
6.2 bar max air pressure with 3/8" diameter
air supply hose.
• Always wear impact-resistant
eye and face protection
when operating or performing
maintenance on this tool
(users and bystanders).
• High sound levels can cause
permanent hearing loss. Always
use
hearing
recommended by your employer
an OSHA regulations while using
this tool (users and bystanders).
• Wear face or dust mask if cutting
operation is dusty.
• Keep
the
tool
operating condition.
• Operators and maintenance personnel
must be physically able to handle the bulk,
weight and power of this tool.
• Air under pressure can cause
severe injury. Never direct air
at yourself or others. Always
turn off the air supply, drain
hose
of
air
detach tool from air supply
before
installing,
or
adjusting
on this tool, or before performing
any maintenance on this tool.
Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check
SXSW1001: Parts Breakdown & Operating Manual
WARNING!
MANUAL
for damaged, frayed or loose hoses and fittings,
and replace immediately. Do not use quick detach
couplings at tool. See instructions for correct set-
up.
MANUAL
ALL
periods of time may be harmful to your hands
and arms. Discontinue use of tool if discomfort,
tingling feeling of pain occurs. Seek medical
advice before resuming use.
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and
firm. Do not overreach when operating the
tool.
• Do not point or indulge in any horseplay with
this tool.
• Anticipate and be alert for sudden changes in
motion during start up and operation of any
power tool.
codes
and
durability of
•
Tool shaft may continue to reciprocate briefly
after throttle is released. Avoid direct contact
with accessorie during and after use. Gloves will
reduce the risk of cuts or burns.
protection
as
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is no
kept away from tool and accessories.
in
efficient
• Do not use (or modify) the tool for any other
purpose than that for which it was designed
without
authorized representative.
• Never force the cutting tool to cut
faster
material than rated capacity.
• NEVER OPERATE THIS TOOL WITHOUT
REQUIRED BLADE GUARD IN PLACE.
pressure
and
removing
any
accessory
WARNING
• Keep tool out of reach of children.
• Air powered tools can vibrate
in use. Vibration, repetitive motions or
uncomfortable positions over extended
• Slipping,
tripping
or falling while operating air tools can
be a major cause of serious injury or
• Do not carry tool by the hose
Protect the hose from sharp objects
and heat.
• Cutting with these tools will create
sharp edges. Wear gloves to
protect hands.
• Cutting edges and blades can
become hot during use.
touch.
• Always hold or clamp material firmly
while working.
• Keep away from reciprocating end of
tool. Do not wear jewelry or loose
clothing. Secure long hair. Scalping
consulting
the
manufacturer's
or
through
heavier
• Use accessories recommended by
SUNEX Tools.
• Do
not
lu bri cate
tools
flam ma ble or vol a tile liq uids such
as ker o sene, die sel or jet fuel.
• This tool is not insulated against
electric shock.
2
• This tool must not be used in
explosive atmospheres.
• Servicing and repairs should only be made
by an authorized service center.
• DON'T FORCE TOOL. Don't force tool or
attachments to do a job for which it was not
designed.
• WEAR PROPER APPAREL.
clothing, neckties, rings, bracelets, or other
jewelry to get caught in moving parts.
Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
and
• DON'T OVEREACH. Keep proper footing
and balance at all times.
• Always be sure blade guard and safety
equipment on saw is operating properly.
• Do not remove any labels. Replace
damaged labels.
• Do not lock, tape or wire the "on/off"
safety lever in the "on" position, as the
lever must be free to return to the "off"
position when released.
• Failure to heed these warnings may reusult
in personal injury and/or property damage.
WARNING:
expose you to chemicals including
nickel which is known to the State of
California to cause cancer and birth defects or
other reproductive harm. For more information
go to www.P65Warnings.ca.gov.
Do not
gauge
with
No loose
This
product
can
07/17/23
Publicidad
