Descargar Imprimir esta página

MORDOMUS iAQ5W Guia De Inicio Rapido

Sensor de calidad del aire

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

EN
iAQ5W – Air quality sensor
Features:
Wi-Fi;
Reading indoor Air quality.
Applications:
Indoor air quality monitoring.
Electrical Specifications:
Power supply voltage: 15VDC
Consumption: 150 mA @ 15VDC
Storage Temperature: -10ºC to 60ºC
Operating Temperature: 10ºC to 50ºC
Maximum humidity: 80% non-condensing
Wireless standards: WI-FI 2,4GHz
Physical Specifications:
iAQ5W
https://
mordomus.com/
mordomus/
docs/wifi/
iAQ5W.pdf
Dimensions: 60mm X 60mm X 20mm.
Protection degree: IP20, for indoor use.
Reading ranges
Temperature: [-40 - +85] ºC
Relative humidity: [0 - 100] %
eCO2: [400 - 65000] ppm
TVOC: [0 - 65000] ppb
AQI-UBA: [1 - 5] level
Wi-Fi connectivity
Wall fixing 1.5m high
After turning on the iAQ5w for the first time, a 1-day calibration period
may be required to stabilize the readings.
ATTENTION:
Mordomus shall not be liable for any damages resulting from the
use of our equipment outside the specifications and/or for a purpose
other than that intended.
Assure Wi-Fi signal strength of at least 2 bars.
Overview:
Power supply connection (15V)
Red Led
Enrollment button
Visual AQI level indicator
AQI-UBA – UBA Air Quality Index
1. Installation
Caution! Before installing the device, make sure that the mains power
is turned off.
1. Disconnect from mains power.
2. Perform the connections according to the schematic.
3. Power up.
2. Connection to WI-FI network and enrollment to Mordomus
Method 1 - Automatic Setup (Router must support WPS)
1. Since factory, on powering up the iAQ5W is in WPS negotiation mode
signaled by the connection status indicator blinking fast continuously.
Take care not to power up more than one iAQ5W device at the same time
since WPS allows for configuration of only one device at a time. We
recommend powering up and registering the devices in a sequential manner.
2. Press the WPS button on the router according to the user manual of this
device and wait until the WPS negotiation is completed. This is signaled by 2
short blinks of the connection status indicator every 2 seconds.
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations →
Modules/Addresses → Plus Button [+]
This mode is limited to 5 minutes in software and on the iAQ5w device for
v.2344
1/8

Publicidad

loading

Resumen de contenidos para MORDOMUS iAQ5W

  • Página 1 – Air quality sensor Take care not to power up more than one iAQ5W device at the same time since WPS allows for configuration of only one device at a time. We recommend powering up and registering the devices in a sequential manner.
  • Página 2 4. Resetting the device to factory defaults safety reasons. 4. After the iAQ5W device shows up in the list make sure to click the button 1. Enter AP mode and access the configuration page as described in section 5. Allow.
  • Página 3 2. Introduza o (SSID) no campo WiFi Name e a palavra passe em WiFi password. Introduza o nome da sua casa no campo Home Name conforme Note que após ligar o iAQ5w pela primeira vez, poderá ser necessário um definido em Mordomus -> Configurações -> Conectividade: O nome da sua período de calibração de 1 dia para estabilizar as leituras.
  • Página 4 WPS) mordomus/docs/wifi/ iAQ5W.pdf 1. Desde fábrica, al encender el iAQ5W está en modo de negociación WPS señalado por el indicador de estado de conexión que parpadea rápidamente de Reserva-se o direito de corrigir quaisquer erros, imprecisões ou omissões forma continua.
  • Página 5 4. Restablecer el dispositivo a los valores predeterminados de 4. Después de que el dispositivo iAQ5W aparezca en la lista, asegúrese de fábrica hacer clic en el botón Permitir. 1. Active el modo PA y acceda a la página de configuración como se describe El indicador del estado de la conexión debe permanecer apagado.
  • Página 6 2 barres, la reproduction peut s'arrêter, bégayer ou même ne pas démarrer. Pour vérifier le niveau de signal actuel, 1. Depuis l'usine, à la mise sous tension, l'iAQ5W est en mode de négociation accédez à : Configurations → Modules/Adresses → Indicateur de niveau WPS signalé...
  • Página 7 5.1. Page de configuration La page de configuration de l’iAQ5W permet une configuration manuelle de: Connexion au routeur. WiFi Name WiFi Password Mordomus Home Name Mordomus Local IP Mordomus port 4. Réinitialisation de l'appareil aux paramètres d'usine Le bouton Reset all réinitialise tous les paramètres ci-dessus et les autres configurations aux valeurs d'usine.
  • Página 8 ES – UBA ÍNDICE DE CALIDAD DEL AIRE FR – UBA INDICE DE QUALITÉ DE L'AIR iAQ5W v.2344...